Wi-Fi

Alpine Linux supports both wireless daemons i.e wpa_supplicant and iwd. This page describes how to set up a wireless network connection with WPA encryption using wpa_supplicant and provides the troubleshooting steps to configure wireless interface/drivers.

Note: Using both wireless daemons i.e wpa_supplicant and iwd simultaneously lead to conflicts.

Prerequisites

Working wireless drivers. In most cases installing linux-firmware should get you the required drivers. Installation of this package can produce errors on diskless or data disk modes. If such errors occur, switch to system disk mode.

To list your available network interfaces:

ip link

or

ip a

Refer to Troubleshooting section to see if you don't see any wireless interfaces (e.g. wlan0). You probably need to load and/or install drivers/firmware. If you are using a Broadcom chipset, see the Broadcom Wi-Fi section.

Bring up the desired interface:

# ip link set wlan0 up

wpa_supplicant

Networking setup-scripts can configure your wifi quickly using wpa_supplicant which can be used with NetworkManager, the standard Linux network configuration tool suite. If the above does not meet your requirement, please follow the steps outlined on this page for manual configuration.

To get started install wpa_supplicant package:

# apk add wpa_supplicant

Use this command to add your Wi-Fi network to wpa_supplicant:

# wpa_passphrase 'ExampleWifiSSID' 'ExampleWifiPassword' > /etc/wpa_supplicant/wpa_supplicant.conf

(Access point not broadcasting its SSID requires additional line scan_ssid=1 in the file /etc/wpa_supplicant/wpa_supplicant.conf)

Note: the Wi-Fi SSID and password are case sensitive and the single quote before and after the SSID and password need to be there

Start wpa_supplicant in the foreground to check if wireless connection succeeds.

# wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf

If all is well, run it as a daemon in the background by setting the -B option.

# wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf

Configure the interface with an IP address.

# udhcpc -i wlan0

Sanity check: the interface should have a inet address.

$ ip addr show wlan0

Automatic Configuration on System Boot

Add a entry for the desired interface (e.g. wlan0) in the file as follows:

Contents of /etc/network/interfaces

auto lo
auto wlan0
iface wlan0 inet dhcp

Warning: Don't remove or comment out the auto lo entry

Sanity check: Make sure /etc/wpa_supplicant/wpa_supplicant.conf is the correct configuration for the wireless access point you want to connect to.

Bring the interface down.

# ip link set wlan0 down

Manually restart (or start) networking.

# rc-service networking --quiet restart &

Perform sanity checks. For issues related to name resolution, refer Networking section.

If all is well, Configure wpa_supplicant to start automatically on boot:

# rc-update add wpa_supplicant boot

Also make sure networking is set to automatically start on boot:

# rc-update add networking boot

Optional security precaution:

By default wpa_supplicant will store your Wi-Fi password in plain text:

Contents of /etc/wpa_supplicant/wpa_supplicant.conf

network={
    ssid="<YourSSIDShouldBeHere>"
        #psk="<YourPasswordShouldBeHereInPlainText>"
    psk=<RandomLettersAndNumbersShouldBeHere>
}

If you dont want your stored password in plain text just delete the line with #psk="<YourPasswordShouldBeHereInPlainText>" on it.

Launching udhcpc through wpa_cli actions

With the above configuration, udhcpc will only run once at boot. If the Wifi isn't available then, or the network changes after booting, udhcpc needs to be notified. You can automatically notify udhcpc of network changes by using a wpa_cli action file, such as the one installed by default at /etc/wpa_supplicant/wpa_cli.sh.

To manually start a wpa_cli daemon with an action file, use the `-a` option:

# wpa_cli -a /etc/wpa_supplicant/wpa_cli.sh

To do this automatically, use the `wpa_cli` service included in wpa_supplicant-openrc:

Contents of /etc/conf.d/wpa_cli

WPACLI_OPTS="-a /etc/wpa_supplicant/wpa_cli.sh"

Add the service to start at boot:

# rc-update add wpa_cli boot

Troubleshooting

Check dmesg

Run dmesg and check for errors related to the wireless interface. Usually, dmesg gives maximum information related to network and all other hardware.

# dmesg

checking network cards

$ cat /proc/net/dev

lists the network interfaces that are detected. If the expected interfaces are not available, Check what network hardware chip you have using lspci or lsusb:

$ lspci -nn

$ lsusb

Refer hardware management, if the default outputs shown above lacks sufficient information.

Check what driver the card uses and modprobe it. Check that the card is in master mode. Check what driver you need on the b43 compatibility page

Broadcom Wi-Fi Chipset Users

The Broadcom chipset is quite popular among older computers. The b43 driver is included in the linux-lts or linux-edge kernel packages. However, you might need to compile the firmware manually for this chipset as it is not included in linux-firmware for some cards.

To check what broadcom chip you have using lspci:

$ lspci -nn -d 14e4:

B43

Download firmware cutter.

$ apk add b43-fwcutter

Now we have everything to download the proprietary driver and extract the firmware from it:

# export FIRMWARE_INSTALL_DIR="/lib/firmware" $ wget http://www.lwfinger.com/b43-firmware/broadcom-wl-5.100.138.tar.bz2 $ tar xjf broadcom-wl-5.100.138.tar.bz2 $ b43-fwcutter -w "$FIRMWARE_INSTALL_DIR" broadcom-wl-5.100.138/linux/wl_apsta.o

More information can be found here.

Now you need to use modprobe so the device will show up:

# modprobe b43

Now continue with the normal instructions.

wl

First install the software we need to build a driver^:

apk add git alpine-sdk linux-headers

Then install the driver build repo (this is archived, however it's legacy so that doesn't matter):

git clone https://github.com/antoineco/broadcom-wl cd broadcom-wl

Then follow the build instructions listed in the git repo:

make doas make install doas depmod -A doas modprobe wl

Reboot and you have a working wl driver. Now continue with the normal instructions.

Rfkill

An error message ioctl 0x8914 failed: No error information, is the busybox ip's way of saying your wireless radio is rfkilled, which means the wireless card is blocked by kernel. This can be changed using rfkill. To show the current status of your Wi-Fi:

~$ rfkill list 0: phy0: wlan Soft blocked: no Hard blocked: no

If the card is hard-blocked, use the hardware button or switch to unblock it. If the card is not hard-blocked but soft-blocked, use the following command:

# rfkill unblock wifi