Wi-Fi: Difference between revisions

Latest revision as of 15:06, 10 January 2025

Alpine Linux supports both wireless daemons i.e wpa_supplicant and iwd. This page describes how to set up a wireless network connection with WPA encryption using wpa_supplicant and provides the troubleshooting steps to configure wireless interface/drivers.

Note: Using both wireless daemons i.e wpa_supplicant and iwd simultaneously lead to conflicts.

Prerequisites

Working wireless drivers. In most cases installing linux-firmware should get you the required drivers. Installation of this package can produce errors on diskless or data disk modes. If such errors occur, switch to system disk mode.

To list your available network interfaces:

ip link

or

ip a

Refer to Troubleshooting section to see if you don't see any wireless interfaces (e.g. wlan0). You probably need to load and/or install drivers/firmware. If you are using a Broadcom chipset, see the Broadcom Wi-Fi section.

Bring up the desired interface:

# ip link set wlan0 up

wpa_supplicant

Networking setup-scripts can configure your wifi quickly using wpa_supplicant which can be used with NetworkManager, the standard Linux network configuration tool suite. If the above does not meet your requirement, please follow the steps outlined on this page for manual configuration.

To get started install wpa_supplicant package:

# apk add wpa_supplicant

Use this command to add your Wi-Fi network to wpa_supplicant:

# wpa_passphrase 'ExampleWifiSSID' 'ExampleWifiPassword' > /etc/wpa_supplicant/wpa_supplicant.conf

(Access point not broadcasting its SSID requires additional line scan_ssid=1 in the file /etc/wpa_supplicant/wpa_supplicant.conf)

Note: the Wi-Fi SSID and password are case sensitive and the single quote before and after the SSID and password need to be there

Start wpa_supplicant in the foreground to check if wireless connection succeeds.

# wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf

Optional security precaution:

By default wpa_supplicant will store your Wi-Fi password in plain text:

Contents of /etc/wpa_supplicant/wpa_supplicant.conf

network={
    ssid="<YourSSIDShouldBeHere>"
        #psk="<YourPasswordShouldBeHereInPlainText>"
    psk=<RandomLettersAndNumbersShouldBeHere>
}

If you dont want your stored password in plain text just delete the line with #psk="<YourPasswordShouldBeHereInPlainText>" on it.

If all is well, run it as a daemon in the background by setting the -B option.

# wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf

Configure the interface with an IP address.

# udhcpc -i wlan0

Sanity check: the interface should have a inet address.

$ ip addr show wlan0

Add a entry for the desired interface (e.g. wlan0) in the file as follows:

Contents of /etc/network/interfaces

auto lo
auto wlan0
iface wlan0 inet dhcp

Warning: Don't remove or comment out the auto lo entry

Sanity check: Make sure /etc/wpa_supplicant/wpa_supplicant.conf is the correct configuration for the wireless access point you want to connect to.

Bring the interface down.

# ip link set wlan0 down

Manually restart (or start) networking.

# rc-service networking --quiet restart &

Perform sanity checks. For issues related to name resolution, refer Networking section.

Service configuration

Proceed to configure wpa_supplicant service to start automatically on boot, if networking works properly:

# rc-update add wpa_supplicant boot

Also ensure that networking is set to automatically start on boot:

# rc-update add networking boot

Manage wpa_supplicant service using the standard start, stop and restart options. For eg: to start wpa_supplicant service:

# rc-service wpa_supplicant start

Launching udhcpc through wpa_cli actions

With the above configuration, udhcpc will only run once at boot. If the Wifi isn't available then, or the network changes after booting, udhcpc needs to be notified. You can automatically notify udhcpc of network changes by using a wpa_cli action file, such as the one installed by default at /etc/wpa_supplicant/wpa_cli.sh.

To manually start a wpa_cli daemon with an action file, use the `-a` option:

# wpa_cli -a /etc/wpa_supplicant/wpa_cli.sh

To do this automatically, use the `wpa_cli` service included in wpa_supplicant-openrc:

Contents of /etc/conf.d/wpa_cli

WPACLI_OPTS="-a /etc/wpa_supplicant/wpa_cli.sh"

Add the service to start at boot:

# rc-update add wpa_cli boot

Troubleshooting

Check dmesg

Run dmesg and check for errors related to the wireless interface. Usually, dmesg gives maximum information related to network and all other hardware.

# dmesg

checking network cards

$ cat /proc/net/dev

lists the network interfaces that are detected. If the expected interfaces are not available, Check what network hardware chip you have using lspci or lsusb:

$ lspci -nn

$ lsusb

Refer hardware management, if the default outputs shown above lacks sufficient information.

Check what driver the card uses and modprobe it. Check that the card is in master mode. Check what driver you need on the b43 compatibility page

Broadcom Wi-Fi Chipset Users

The Broadcom chipset is quite popular among older computers. The b43 driver is included in the linux-lts or linux-edge kernel packages. However, you might need to compile the firmware manually for this chipset as it is not included in linux-firmware for some cards.

To check what broadcom chip you have using lspci:

$ lspci -nn -d 14e4:

B43

Download firmware cutter.

$ apk add b43-fwcutter

Now we have everything to download the proprietary driver and extract the firmware from it:

# export FIRMWARE_INSTALL_DIR="/lib/firmware" $ wget http://www.lwfinger.com/b43-firmware/broadcom-wl-5.100.138.tar.bz2 $ tar xjf broadcom-wl-5.100.138.tar.bz2 $ b43-fwcutter -w "$FIRMWARE_INSTALL_DIR" broadcom-wl-5.100.138/linux/wl_apsta.o

More information can be found here.

Now you need to use modprobe so the device will show up:

# modprobe b43

Now continue with the normal instructions.

wl

First install the software we need to build a driver^:

apk add git alpine-sdk linux-headers

Then install the driver build repo (this is archived, however it's legacy so that doesn't matter):

git clone https://github.com/antoineco/broadcom-wl cd broadcom-wl

Then follow the build instructions listed in the git repo:

make doas make install doas depmod -A doas modprobe wl

Reboot and you have a working wl driver. Now continue with the normal instructions.

Rfkill

An error message ioctl 0x8914 failed: No error information, is the busybox ip's way of saying your wireless radio is rfkilled, which means the wireless card is blocked by kernel. This can be changed using rfkill. To show the current status of your Wi-Fi:

~$ rfkill list 0: phy0: wlan Soft blocked: no Hard blocked: no

If the card is hard-blocked, use the hardware button or switch to unblock it. If the card is not hard-blocked but soft-blocked, use the following command:

# rfkill unblock wifi

@@ Line 1: / Line 1: @@
-This page describes how to set up a wireless network connection with WPA encryption using [[#wpa_supplicant|wpa_supplicant]].
+Alpine Linux supports both wireless daemons i.e [[#wpa_supplicant|wpa_supplicant]] and [[iwd]]. This page describes how to set up a wireless network connection with WPA encryption using [[#wpa_supplicant|wpa_supplicant]] and provides the troubleshooting steps to configure wireless interface/drivers.
+{{Note|Using both wireless daemons i.e [[#wpa_supplicant|wpa_supplicant]] and [[iwd]] simultaneously lead to conflicts.}}
 == Prerequisites ==
 Working wireless drivers. In most cases installing {{Pkg|linux-firmware}} should get you the required drivers. Installation of this package can produce errors on diskless or data disk modes. If such errors occur, switch to system disk mode.
-To list your available network interfaces:
+To list your available network interfaces: {{Cmd|ip link}}
+or {{Cmd|ip a}}
-{{Cmd|ip link}}
-or
-{{Cmd|ip a}}
 Refer to [[#Troubleshooting|Troubleshooting]] section to see if you don't see any wireless interfaces (e.g. {{Path|wlan0}}). You probably need to load and/or install drivers/firmware. If you are using a '''Broadcom chipset''', see the [[#Broadcom_Wi-Fi_Chipset_Users|Broadcom Wi-Fi section]].
-Bring up the desired interface:
+Bring up the desired interface: {{Cmd|# ip link set wlan0 up}}
-{{Cmd|# ip link set wlan0 up}}
-If this errors with <code>ioctl 0x8914 failed: No error information</code>, that's <code>busybox ip</code>'s way of saying your wireless radio is rfkill'd. See the [[#Rfkill|Rfkill section]] for information on how to unblock your wireless radio.
-== iwd ==
-{{main|iwd }}
-{{Tip| [[NetworkManager]],  the standard Linux network configuration tool suite supports both wireless daemons i.e [[iwd]] and [[#wpa_supplicant|wpa_supplicant]]. Using both may lead to conflicts.}}
 == wpa_supplicant  ==
+{{Seealso|iwd}}
-[[Configure_Networking#Network_setup-scripts|Network setup-scripts]] can configure your wifi quickly using <code>wpa_supplicant</code>. If it does not meet your requirement, please follow the steps outlined on this page.
+Networking [[Configure_Networking#Network_setup-scripts|setup-scripts]] can configure your wifi quickly using <code>wpa_supplicant</code> which can be used with [[NetworkManager]], the standard Linux network configuration tool suite.  If the above does not meet your requirement, please follow the steps outlined on this page for manual configuration.
-To get started install {{Pkg|wpa_supplicant}}
+To get started install {{Pkg|wpa_supplicant}} package: {{Cmd|# apk add wpa_supplicant}}
-{{Cmd|# apk add wpa_supplicant}}
+Use this command to add your Wi-Fi network to wpa_supplicant: {{Cmd|# wpa_passphrase 'ExampleWifiSSID' 'ExampleWifiPassword' > /etc/wpa_supplicant/wpa_supplicant.conf}}
+''(Access point not broadcasting its SSID requires additional line <code>scan_ssid=1</code> in the file {{Path|/etc/wpa_supplicant/wpa_supplicant.conf}})''
-Use this command to add your Wi-Fi network to wpa_supplicant:
-{{Cmd|# wpa_passphrase 'ExampleWifiSSID' 'ExampleWifiPassword' > /etc/wpa_supplicant/wpa_supplicant.conf}}
-''(Access point not broadcasting its SSID requires additional line <code>scan_ssid=1</code> in the file <code>wpa_supplicant.conf</code>)''
 {{Note|the Wi-Fi SSID and password are case sensitive and the single quote before and after the SSID and password need to be there}}
-Start wpa_supplicant in the foreground to make sure the connection succeeds.
+Start wpa_supplicant in the foreground to check if wireless connection succeeds.{{Cmd|# wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf}}
-{{Cmd|# wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf}}
-<br>
+'''Optional security precaution:'''
-If all is well, run it as a daemon in the background by setting the {{Path|-B}} option.
-{{Cmd|# wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf}}
-<br>
+By default {{Pkg|wpa_supplicant}} will store your Wi-Fi password in plain text:{{Cat|/etc/wpa_supplicant/wpa_supplicant.conf|<nowiki>network={
-Configure the interface with an IP address.
+    ssid="<YourSSIDShouldBeHere>"
-{{Cmd|# udhcpc -i wlan0}}
+        #psk="<YourPasswordShouldBeHereInPlainText>"
+    psk=<RandomLettersAndNumbersShouldBeHere>
+}</nowiki>}}
+If you dont want your stored password in plain text just delete the line with <code>#psk="<YourPasswordShouldBeHereInPlainText>"</code> on it.
-Sanity check: the interface should have a {{Path|inet}} address.
+If all is well, run it as a daemon in the background by setting the {{Path|-B}} option. {{Cmd|# wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf}}
-{{Cmd|$ ip addr show wlan0}}
-<br>
+Configure the interface with an IP address.{{Cmd|# udhcpc -i wlan0}}
-=== Automatic Configuration on System Boot  ===
+Sanity check: the interface should have a {{Path|inet}} address. {{Cmd|$ ip addr show wlan0}}
-Add a entry for the desired interface (e.g. {{Path|wlan0}}):
+Add a entry for the desired interface (e.g. <code>wlan0</code>) in the file as follows:{{Cat|/etc/network/interfaces|auto lo
-{{Cat|/etc/network/interfaces|auto lo
 auto wlan0
 iface wlan0 inet dhcp}}
@@ Line 65: / Line 49: @@
 Sanity check: Make sure {{Path|/etc/wpa_supplicant/wpa_supplicant.conf}} is the correct configuration for the wireless access point you want to connect to.
-Bring the interface down.
+Bring the interface down. {{Cmd|# ip link set wlan0 down}}
-{{Cmd|# ip link set wlan0 down}}
-<br>
-Manually restart (or '''start''') '''networking'''.
-{{Cmd|# rc-service networking --quiet restart &}}
-<br>
-Perform sanity checks like ping and browsing. For issues related to name resolution, refer [[Configure_Networking#Configuring_DNS|Networking]] page.
-If all is well, Configure wpa_supplicant to start automatically on boot:
+Manually restart (or '''start''') '''networking'''.{{Cmd|# rc-service networking --quiet restart &}}
-{{Cmd|# rc-update add wpa_supplicant boot}}
+Perform [[Configure_Networking#Connectivity_testing|sanity checks]]. For issues related to name resolution, refer [[Configure_Networking#Configuring_DNS|Networking]] section.
-Also make sure '''networking''' is set to automatically start on boot:
+=== Service configuration ===
-{{Cmd|# rc-update add networking boot}}
+Proceed to configure wpa_supplicant service to start automatically on boot, if networking works properly: {{Cmd|# rc-update add wpa_supplicant boot}}
+Also ensure that '''networking''' is set to automatically start on boot: {{Cmd|# rc-update add networking boot}}
-'''Optional security precaution:'''
+Manage wpa_supplicant service using the standard '''start''', '''stop''' and '''restart''' options. For eg: to start wpa_supplicant service: {{Cmd|# rc-service wpa_supplicant start}}
-By default {{Pkg|wpa_supplicant}} will store your Wi-Fi password in plain text:
-{{Cat|(Example) /etc/wpa_supplicant/wpa_supplicant.conf|<nowiki>network={
-    ssid="<YourSSIDShouldBeHere>"
-        #psk="<YourPasswordShouldBeHereInPlainText>"
-    psk=<RandomLettersAndNumbersShouldBeHere>
-}</nowiki>}}
-this is not necessary and {{Pkg|wpa_supplicant}} should funtion just fine without it, if you dont want your stored password in plain text just delete the line with <code>#psk="<YourPasswordShouldBeHereInPlainText>"</code> on it.
 === Launching udhcpc through wpa_cli actions ===
-With the above configuration, udhcpc will only run once at boot.
+With the above configuration, udhcpc will only run once at boot. If the Wifi isn't available then, or the network changes after booting, udhcpc needs to be notified. You can automatically notify udhcpc of network changes by using a wpa_cli action file, such as the one installed by default at {{Path|/etc/wpa_supplicant/wpa_cli.sh}}.
-If the Wifi isn't available then, or the network changes after booting, udhcpc needs to be notified.
-You can automatically notify udhcpc of network changes by using a wpa_cli action file, such as the one installed by default at `/etc/wpa_supplicant/wpa_cli.sh`.
-To manually start a wpa_cli daemon with an action file, use the `-a` option:
-{{Cmd|# wpa_cli -a /etc/wpa_supplicant/wpa_cli.sh}}
-<br>
+To manually start a wpa_cli daemon with an action file, use the `-a` option: {{Cmd|# wpa_cli -a /etc/wpa_supplicant/wpa_cli.sh}}
-To do this automatically, use the `wpa_cli` service included in {{Pkg|wpa_supplicant-openrc}}:
-{{Cat|/etc/conf.d/wpa_cli|<nowiki>WPACLI_OPTS="-a /etc/wpa_supplicant/wpa_cli.sh"</nowiki>}}
+To do this automatically, use the `wpa_cli` service included in {{Pkg|wpa_supplicant-openrc}}: {{Cat|/etc/conf.d/wpa_cli|<nowiki>WPACLI_OPTS="-a /etc/wpa_supplicant/wpa_cli.sh"</nowiki>}}
+Add the service to start at boot: {{Cmd|# rc-update add wpa_cli boot}}
-{{Cmd|# rc-update add wpa_cli boot}}
 == Troubleshooting ==
@@ Line 119: / Line 76: @@
 Run dmesg and check for errors related to the wireless interface. Usually, dmesg gives maximum information related to network and all other hardware.
-{{Cmd|# dmesg |grep wlan}}
-or
 {{Cmd|# dmesg}}
@@ Line 145: / Line 100: @@
 ====B43====
-Download firmware cutter.
+Download firmware cutter. {{Cmd|$ apk add b43-fwcutter}}
-{{Cmd|$ apk add b43-fwcutter}}
+Now we have everything to download the proprietary driver and extract the firmware from it: {{Cmd|<nowiki># export FIRMWARE_INSTALL_DIR="/lib/firmware"
-Now we have everything to download the proprietary driver and extract the firmware from it:
-{{Cmd|<nowiki># export FIRMWARE_INSTALL_DIR="/lib/firmware"
 $ wget http://www.lwfinger.com/b43-firmware/broadcom-wl-5.100.138.tar.bz2
 $ tar xjf broadcom-wl-5.100.138.tar.bz2
@@ Line 158: / Line 109: @@
 More information can be found [http://linuxwireless.sipsolutions.net/en/users/Drivers/b43/#Other_distributions_not_mentioned_above here].
-Now you need to use modprobe so the device will show up:
+Now you need to use modprobe so the device will show up: {{Cmd|# modprobe b43}}
-{{Cmd|# modprobe b43}}
 Now continue with the normal instructions.
@@ Line 166: / Line 115: @@
 ====wl====
-First install the software we need to build a driver[https://unix.stackexchange.com/questions/606073/how-to-build-kernel-modules-in-alpine-3-12 ^]:
+First install the software we need to build a driver[https://unix.stackexchange.com/questions/606073/how-to-build-kernel-modules-in-alpine-3-12 ^]: {{Cmd|apk add git alpine-sdk linux-headers}}
-{{Cmd|apk add git alpine-sdk linux-headers}}
+Then install the driver build repo (this is archived, however it's legacy so that doesn't matter): {{Cmd|git clone https://github.com/antoineco/broadcom-wl
-Then install the driver build repo (this is archived, however it's legacy so that doesn't matter):
-{{Cmd|git clone https://github.com/antoineco/broadcom-wl
 cd broadcom-wl
 }}
-Then follow the build instructions listed in the git repo:
+Then follow the build instructions listed in the git repo: {{Cmd|make
-{{Cmd|make
 doas make install
 doas depmod -A
@@ Line 184: / Line 127: @@
 }}
-reboot and you have a working wl driver!
+Reboot and you have a working wl driver. Now continue with the normal instructions.
-Now continue with the normal instructions.
 === Rfkill ===
-Many laptops have a hardware button (or switch) to turn off wireless card, however, the card can also be blocked by kernel. This can be changed using rfkill. To show the current of your Wi-Fi:
+An error message <code>ioctl 0x8914 failed: No error information</code>, is the <code>busybox ip</code>'s way of saying your wireless radio is rfkilled, which means the wireless card is blocked by kernel. This can be changed using rfkill. To show the current status of your Wi-Fi:
 <p style="background-color:#f9f9f9; border:1px dashed #2f6fab; line-height:1.1em; padding:1em; font-family:monospace; font-size:10pt; white-space:pre; overflow:auto;"><span style="color:green;">~</span>'''$''' rfkill list
 : phy0: wlan
@@ Line 198: / Line 138: @@
 </p>
-<br>
+If the card is hard-blocked, use the hardware button or switch to unblock it. If the card is not hard-blocked but soft-blocked, use the following command: {{Cmd|# rfkill unblock wifi}}
-If the card is hard-blocked, use the hardware button or switch to unblock it. If the card is not hard-blocked but soft-blocked, use the following command:
-{{Cmd|# rfkill unblock wifi}}
-<br>
 == See Also ==