Wi-Fi: Difference between revisions

From Alpine Linux
No edit summary
m (rephrased sentence about Network manager)
 
(70 intermediate revisions by 26 users not shown)
Line 1: Line 1:
This document describes how to set up a wireless network connection with WPA encryption.
This page describes how to set up a wireless network connection with WPA encryption using [[#wpa_supplicant|wpa_supplicant]].  


First make sure your wireless drivers are loaded properly. (if you are using a '''Broadcom chipset''', see the [[#Broadcom_Wi-Fi_Chipset_Users|section at the bottom of this post]].)
== Prerequisites ==


Install {{Pkg|wireless-tools}} and {{Pkg|wpa_supplicant}}.
Working wireless drivers. In most cases installing {{Pkg|linux-firmware}} should get you the required drivers. Installation of this package can produce errors on diskless or data disk modes. If such errors occur, switch to system disk mode.
{{Cmd|apk add wireless-tools wpa_supplicant}}
To list your available network interfaces:


Bring the link up so we can look for wireless networks. (An error here means you probably need extra drivers/firmware.)
{{Cmd|ip link}}
{{Cmd|ip link set wlan0 up}}


Find a network to connect to. Look for the ESSID. In this example we will use the ESSID "MyNet".
or
{{Cmd|iwlist wlan0 scanning}}


Let's set the ESSID:
{{Cmd|ip a}}
{{Cmd|iwconfig wlan0 essid MyNet}}


We need to create a shared key for wpa_supplicant.
Refer to [[#Troubleshooting|Troubleshooting]] section to see if you don't see any wireless interfaces (e.g. {{Path|wlan0}}). You probably need to load and/or install drivers/firmware. If you are using a '''Broadcom chipset''', see the [[#Broadcom_Wi-Fi_Chipset_Users|Broadcom Wi-Fi section]].
{{Cmd|wpa_passphrase MyNet > wpa.conf}}
It will wait for the password from stdin. Enter the password and enter. Now you will have a {{Path|wpa.conf}} file with the preshared key.


Start wpa_supplicant with the generated config:
Bring up the desired interface:
{{Cmd|wpa_supplicant -Dwext -iwlan0 -c ./wpa.conf}}
{{Cmd|# ip link set wlan0 up}}


From another console, start dhcpcd:
If this errors with <code>ioctl 0x8914 failed: No error information</code>, that's <code>busybox ip</code>'s way of saying your wireless radio is rfkill'd. See the [[#Rfkill|Rfkill section]] for information on how to unblock your wireless radio.
{{Cmd|udhcpc -i wlan0}}


You should get an IP address.
== iwd ==
{{main|iwd }}


You then want to make the connection process automatic on boot-up.  Open {{Path|/etc/network/interfaces}} and add the following stanza:
{{Tip| [[NetworkManager]],  the standard Linux network configuration tool suite supports both wireless daemons i.e [[iwd]] and [[#wpa_supplicant|wpa_supplicant]]. Using both may lead to conflicts.}}
auto wlan0
iface wlan0 inet dhcp
{{Note|I had to append `pre-up iwconfig wlan0 essid <ESSID>` to automatically connect to the network.}}


You will also need to set wpa_supplicant to start automatically on boot:
== wpa_supplicant ==
{{Cmd|rc-update add wpa_supplicant boot}}


Next, create {{Path|/etc/wpa_supplicant/}} (permissions of 755 with root:root are fine), and move {{Path|wpa.conf}} into that folder, renaming it to {{Path|wpa_supplicant.conf}}.
[[Configure_Networking#Network_setup-scripts|Network setup-scripts]] can configure your wifi quickly using <code>wpa_supplicant</code>. If it does not meet your requirement, please follow the steps outlined on this page.  


Reboot and check that you are associated with the access point:
To get started install {{Pkg|wpa_supplicant}}
{{Cmd|iwconfig wlan0}}
and check that you got a DHCP lease:
{{Cmd|ifconfig wlan0 {{!}} grep addr}}


== Broadcom Wi-Fi Chipset Users  ==
{{Cmd|# apk add wpa_supplicant}}
The Broadcom chipset is quite popular among older computers. You will need to compile the firmware manually for this chipset as it is not included.


You can check if you have a Broadcom chipset by using dmesg:
Use this command to add your Wi-Fi network to wpa_supplicant:
{{Cmd|# wpa_passphrase 'ExampleWifiSSID' 'ExampleWifiPassword' > /etc/wpa_supplicant/wpa_supplicant.conf}}
''(Access point not broadcasting its SSID requires additional line <code>scan_ssid=1</code> in the file <code>wpa_supplicant.conf</code>)''


{{Cmd|dmesg {{!}} grep Broadcom}}
{{Note|the Wi-Fi SSID and password are case sensitive and the single quote before and after the SSID and password need to be there}}


First install the SDK an Git:
Start wpa_supplicant in the foreground to make sure the connection succeeds.
{{Cmd|apk add alpine-sdk git}}
{{Cmd|# wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf}}


Then git clone aports from git.alpinelinux.org.
<br>
If all is well, run it as a daemon in the background by setting the {{Path|-B}} option.
{{Cmd|# wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf}}


(remove $, new users can't add links to the wiki)
<br>
Configure the interface with an IP address.
{{Cmd|# udhcpc -i wlan0}}


{{Cmd|git clone git:/$/git.alpinelinux.org/abuild}}
Sanity check: the interface should have a {{Path|inet}} address.
{{Cmd|$ ip addr show wlan0}}


Change your directory to '''aports/non-free/b43-firmware''', then build it.
<br>


''You can't be root and must be a user of the group abuild (use groupadd)''
=== Automatic Configuration on System Boot  ===


{{Cmd|abuild -r}}
Add a entry for the desired interface (e.g. {{Path|wlan0}}):
{{Cat|/etc/network/interfaces|auto lo
auto wlan0
iface wlan0 inet dhcp}}


Install the generated packge file (it will be in ~/packages/) - make sure to pass '''--allow-untrusted'''
{{Warning|Don't remove or comment out the '''auto lo''' entry}}


{{Cmd|apk add --allow-untrusted ~/packages/...pkg}}
Sanity check: Make sure {{Path|/etc/wpa_supplicant/wpa_supplicant.conf}} is the correct configuration for the wireless access point you want to connect to.


Now we need fwcutter, which is executed from the firmware package:
Bring the interface down.


{{Cmd|apk add b43-fwcutter b43-firmware}}
{{Cmd|# ip link set wlan0 down}}
 
<br>
Manually restart (or '''start''') '''networking'''.
 
{{Cmd|# rc-service networking --quiet restart &}}
 
<br>
Perform sanity checks like ping and browsing. For issues related to name resolution, refer [[Configure_Networking#Configuring_DNS|Networking]] page.
 
If all is well, Configure wpa_supplicant to start automatically on boot:
 
{{Cmd|# rc-update add wpa_supplicant boot}}
 
Also make sure '''networking''' is set to automatically start on boot:
 
{{Cmd|# rc-update add networking boot}}
 
'''Optional security precaution:'''
 
By default {{Pkg|wpa_supplicant}} will store your Wi-Fi password in plain text:
 
{{Cat|(Example) /etc/wpa_supplicant/wpa_supplicant.conf|<nowiki>network={
    ssid="<YourSSIDShouldBeHere>"
        #psk="<YourPasswordShouldBeHereInPlainText>"
    psk=<RandomLettersAndNumbersShouldBeHere>
}</nowiki>}}
 
this is not necessary and {{Pkg|wpa_supplicant}} should funtion just fine without it, if you dont want your stored password in plain text just delete the line with <code>#psk="<YourPasswordShouldBeHereInPlainText>"</code> on it.
 
=== Launching udhcpc through wpa_cli actions ===
 
With the above configuration, udhcpc will only run once at boot.
If the Wifi isn't available then, or the network changes after booting, udhcpc needs to be notified.
You can automatically notify udhcpc of network changes by using a wpa_cli action file, such as the one installed by default at `/etc/wpa_supplicant/wpa_cli.sh`.
 
To manually start a wpa_cli daemon with an action file, use the `-a` option:
 
{{Cmd|# wpa_cli -a /etc/wpa_supplicant/wpa_cli.sh}}
 
<br>
To do this automatically, use the `wpa_cli` service included in {{Pkg|wpa_supplicant-openrc}}:
 
{{Cat|/etc/conf.d/wpa_cli|<nowiki>WPACLI_OPTS="-a /etc/wpa_supplicant/wpa_cli.sh"</nowiki>}}
 
{{Cmd|# rc-update add wpa_cli boot}}
 
== Troubleshooting ==
 
=== Check dmesg ===
 
Run dmesg and check for errors related to the wireless interface. Usually, dmesg gives maximum information related to network and all other hardware.
{{Cmd|# dmesg |grep wlan}}
or
{{Cmd|# dmesg}}
 
=== checking network cards ===
 
{{Cmd|$ cat /proc/net/dev }} lists the network interfaces that are detected. If the expected interfaces are not available, Check what network hardware chip you have using lspci or lsusb:
 
{{Cmd|$ lspci -nn }}
{{Cmd|$ lsusb }}
 
Refer [[How to get regular stuff working#Hardware_Management|hardware management]], if the default outputs shown above lacks sufficient information.
 
Check what driver the card uses and modprobe it. Check that the card is in master mode.
Check what driver you need on the [https://wireless.wiki.kernel.org/en/users/Drivers/b43#list_of_hardware b43 compatibility page]
 
=== Broadcom Wi-Fi Chipset Users  ===
 
The Broadcom chipset is quite popular among older computers. The b43 driver is included in the linux-lts or linux-edge kernel packages. However, you might need to compile the firmware manually for this chipset as it is not included in linux-firmware for some cards.
 
To check what broadcom chip you have using lspci:
 
{{Cmd|$ lspci -nn -d 14e4:}}
 
====B43====
 
Download firmware cutter.
 
{{Cmd|$ apk add b43-fwcutter}}
 
Now we have everything to download the proprietary driver and extract the firmware from it:
 
{{Cmd|<nowiki># export FIRMWARE_INSTALL_DIR="/lib/firmware"
$ wget http://www.lwfinger.com/b43-firmware/broadcom-wl-5.100.138.tar.bz2
$ tar xjf broadcom-wl-5.100.138.tar.bz2
$ b43-fwcutter -w "$FIRMWARE_INSTALL_DIR" broadcom-wl-5.100.138/linux/wl_apsta.o</nowiki>}}
 
More information can be found [http://linuxwireless.sipsolutions.net/en/users/Drivers/b43/#Other_distributions_not_mentioned_above here].


Now you need to use modprobe so the device will show up:
Now you need to use modprobe so the device will show up:


{{Cmd|modprobe b43}}
{{Cmd|# modprobe b43}}
 
Now continue with the normal instructions.
 
====wl====
 
First install the software we need to build a driver[https://unix.stackexchange.com/questions/606073/how-to-build-kernel-modules-in-alpine-3-12 ^]:
 
{{Cmd|apk add git alpine-sdk linux-headers}}
 
Then install the driver build repo (this is archived, however it's legacy so that doesn't matter):
 
{{Cmd|git clone https://github.com/antoineco/broadcom-wl
cd broadcom-wl
}}


To automate this on startup add it to /etc/modules:
Then follow the build instructions listed in the git repo:


{{Cmd|echo b43 >> /etc/modules}}
{{Cmd|make
doas make install
doas depmod -A
doas modprobe wl
}}
 
reboot and you have a working wl driver!


Now continue with the normal instructions.  
Now continue with the normal instructions.  
=== Rfkill ===
Many laptops have a hardware button (or switch) to turn off wireless card, however, the card can also be blocked by kernel. This can be changed using rfkill. To show the current of your Wi-Fi:
<p style="background-color:#f9f9f9; border:1px dashed #2f6fab; line-height:1.1em; padding:1em; font-family:monospace; font-size:10pt; white-space:pre; overflow:auto;"><span style="color:green;">~</span>'''$''' rfkill list
0: phy0: wlan
    Soft blocked: no
    Hard blocked: no
</p>
<br>
If the card is hard-blocked, use the hardware button or switch to unblock it. If the card is not hard-blocked but soft-blocked, use the following command:
{{Cmd|# rfkill unblock wifi}}
<br>
== See Also ==
* [[Configure_Networking| Networking in Alpine Linux]]
* [[Iwd|iwd]] - An alternate to wpa_supplicant
* [[NetworkManager]] - Front-end to Networking
* [https://wiki.postmarketos.org/wiki/WiFi PostmarketOS Wiki]
* [https://wiki.archlinux.org/title/Network_configuration/Wireless Archwiki]
* [https://wiki.gentoo.org/wiki/Wi-Fi Gentoo Wiki]


[[Category:Networking]]
[[Category:Networking]]

Latest revision as of 10:42, 18 October 2024

This page describes how to set up a wireless network connection with WPA encryption using wpa_supplicant.

Prerequisites

Working wireless drivers. In most cases installing linux-firmware should get you the required drivers. Installation of this package can produce errors on diskless or data disk modes. If such errors occur, switch to system disk mode. To list your available network interfaces:

ip link

or

ip a

Refer to Troubleshooting section to see if you don't see any wireless interfaces (e.g. wlan0). You probably need to load and/or install drivers/firmware. If you are using a Broadcom chipset, see the Broadcom Wi-Fi section.

Bring up the desired interface:

# ip link set wlan0 up

If this errors with ioctl 0x8914 failed: No error information, that's busybox ip's way of saying your wireless radio is rfkill'd. See the Rfkill section for information on how to unblock your wireless radio.

iwd

Main article: iwd
Tip: NetworkManager, the standard Linux network configuration tool suite supports both wireless daemons i.e iwd and wpa_supplicant. Using both may lead to conflicts.

wpa_supplicant

Network setup-scripts can configure your wifi quickly using wpa_supplicant. If it does not meet your requirement, please follow the steps outlined on this page.

To get started install wpa_supplicant

# apk add wpa_supplicant

Use this command to add your Wi-Fi network to wpa_supplicant:

# wpa_passphrase 'ExampleWifiSSID' 'ExampleWifiPassword' > /etc/wpa_supplicant/wpa_supplicant.conf

(Access point not broadcasting its SSID requires additional line scan_ssid=1 in the file wpa_supplicant.conf)

Note: the Wi-Fi SSID and password are case sensitive and the single quote before and after the SSID and password need to be there

Start wpa_supplicant in the foreground to make sure the connection succeeds.

# wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf


If all is well, run it as a daemon in the background by setting the -B option.

# wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf


Configure the interface with an IP address.

# udhcpc -i wlan0

Sanity check: the interface should have a inet address.

$ ip addr show wlan0


Automatic Configuration on System Boot

Add a entry for the desired interface (e.g. wlan0):

Contents of /etc/network/interfaces

auto lo auto wlan0 iface wlan0 inet dhcp
Warning: Don't remove or comment out the auto lo entry


Sanity check: Make sure /etc/wpa_supplicant/wpa_supplicant.conf is the correct configuration for the wireless access point you want to connect to.

Bring the interface down.

# ip link set wlan0 down


Manually restart (or start) networking.

# rc-service networking --quiet restart &


Perform sanity checks like ping and browsing. For issues related to name resolution, refer Networking page.

If all is well, Configure wpa_supplicant to start automatically on boot:

# rc-update add wpa_supplicant boot

Also make sure networking is set to automatically start on boot:

# rc-update add networking boot

Optional security precaution:

By default wpa_supplicant will store your Wi-Fi password in plain text:

Contents of (Example) /etc/wpa_supplicant/wpa_supplicant.conf

network={ ssid="<YourSSIDShouldBeHere>" #psk="<YourPasswordShouldBeHereInPlainText>" psk=<RandomLettersAndNumbersShouldBeHere> }

this is not necessary and wpa_supplicant should funtion just fine without it, if you dont want your stored password in plain text just delete the line with #psk="<YourPasswordShouldBeHereInPlainText>" on it.

Launching udhcpc through wpa_cli actions

With the above configuration, udhcpc will only run once at boot. If the Wifi isn't available then, or the network changes after booting, udhcpc needs to be notified. You can automatically notify udhcpc of network changes by using a wpa_cli action file, such as the one installed by default at `/etc/wpa_supplicant/wpa_cli.sh`.

To manually start a wpa_cli daemon with an action file, use the `-a` option:

# wpa_cli -a /etc/wpa_supplicant/wpa_cli.sh


To do this automatically, use the `wpa_cli` service included in wpa_supplicant-openrc:

Contents of /etc/conf.d/wpa_cli

WPACLI_OPTS="-a /etc/wpa_supplicant/wpa_cli.sh"

# rc-update add wpa_cli boot

Troubleshooting

Check dmesg

Run dmesg and check for errors related to the wireless interface. Usually, dmesg gives maximum information related to network and all other hardware.

# dmesg

or

# dmesg

checking network cards

$ cat /proc/net/dev

lists the network interfaces that are detected. If the expected interfaces are not available, Check what network hardware chip you have using lspci or lsusb:

$ lspci -nn

$ lsusb

Refer hardware management, if the default outputs shown above lacks sufficient information.

Check what driver the card uses and modprobe it. Check that the card is in master mode. Check what driver you need on the b43 compatibility page

Broadcom Wi-Fi Chipset Users

The Broadcom chipset is quite popular among older computers. The b43 driver is included in the linux-lts or linux-edge kernel packages. However, you might need to compile the firmware manually for this chipset as it is not included in linux-firmware for some cards.

To check what broadcom chip you have using lspci:

$ lspci -nn -d 14e4:

B43

Download firmware cutter.

$ apk add b43-fwcutter

Now we have everything to download the proprietary driver and extract the firmware from it:

# export FIRMWARE_INSTALL_DIR="/lib/firmware" $ wget http://www.lwfinger.com/b43-firmware/broadcom-wl-5.100.138.tar.bz2 $ tar xjf broadcom-wl-5.100.138.tar.bz2 $ b43-fwcutter -w "$FIRMWARE_INSTALL_DIR" broadcom-wl-5.100.138/linux/wl_apsta.o

More information can be found here.

Now you need to use modprobe so the device will show up:

# modprobe b43

Now continue with the normal instructions.

wl

First install the software we need to build a driver^:

apk add git alpine-sdk linux-headers

Then install the driver build repo (this is archived, however it's legacy so that doesn't matter):

git clone https://github.com/antoineco/broadcom-wl cd broadcom-wl

Then follow the build instructions listed in the git repo:

make doas make install doas depmod -A doas modprobe wl

reboot and you have a working wl driver!

Now continue with the normal instructions.

Rfkill

Many laptops have a hardware button (or switch) to turn off wireless card, however, the card can also be blocked by kernel. This can be changed using rfkill. To show the current of your Wi-Fi:

~$ rfkill list 0: phy0: wlan Soft blocked: no Hard blocked: no


If the card is hard-blocked, use the hardware button or switch to unblock it. If the card is not hard-blocked but soft-blocked, use the following command:

# rfkill unblock wifi


See Also

Retrieved from "https://wiki.alpinelinux.org/w/index.php?title=Wi-Fi&oldid=27600"