{{Obsolete|The AMD Geode LX800 processor used on this board does not support the SSE instruction required to run modern versions of Alpine Linux.}}
It was not possible to install OpenVPN in ether the thinclient or the SIP-phone, so we needed a OpenVPN gateway.
...
10 KB (1,501 words) - 07:48, 13 January 2024
Nginx package is available in the Alpine Linux repositories. To install it run:
...r_processes auto; # it will be determinate automatically by the number of core
...
5 KB (731 words) - 10:37, 17 November 2023
Multipath storage I/O is not abled by default on Alpine Linux installation media. Multipath I/O on Linux depends on ''dev
If we are happy with the configuration, let's add ''openrc'' daemons.
...
4 KB (609 words) - 09:47, 26 September 2023
...a pool that is located in an encrypted partition. To encrypt the partition the Device Mapper crypt (dm-crypt) module and Linux Unified Key Setup (LUKS) is
Note that you must install the <code>/boot/</code> directory on an unecrypted partition to boot correctly.
...
10 KB (1,601 words) - 05:46, 26 August 2023
...traffic from your main static IP (on your openvpn server) over a tunnel to the remote location.
...remote location will require internet access. They will be provided with the following equipment:
...
8 KB (1,182 words) - 18:47, 20 December 2021
This article complements the existing installation instructions for Raspberry Pi,
providing only the needed changes that enable booting from an encrypted media. Use it only as
...
5 KB (773 words) - 21:00, 24 May 2024
...tures or outdated hardware, to reduce bloat further, to tune the kernel to the hardware.
...pense of some responsiveness, and support for many devices. You can tweak the kernel for desktop use and low latency and responsiveness.
...
12 KB (1,972 words) - 22:25, 29 December 2023
...nitial article to work. I haven't duplicated everything here however, just the stuff that relates to IPv6.
...e to implement IPv6 addressing on VLAN 3 to carry your IPv6 traffic out of the VPN. If your ISP gives you IPv6 addressing you may still implement addressi
...
52 KB (7,613 words) - 20:28, 30 August 2023
The menu choices that are provided by <code>setup-alpine</code> might not cover
...s) and [[Alpine_setup_scripts#Partitioning|tell setup-disk]] to install to the prepared target mountpoint.
...
20 KB (2,782 words) - 22:56, 4 March 2024
== What is edge (The Definition) ==
* tree on the cliff
...
4 KB (691 words) - 01:34, 27 June 2022
Begin by booting from the Alpine Linux installation media in the usual way. Log in as `root`, run `setup-alpine`, and answer `none` when ask
...s. In my case the SSD disk is found as sda, so I will use 'sda' throughout the process.
...
4 KB (619 words) - 10:55, 7 August 2023
...ost of the common maintenance scripts work with PostgreSQL however some of the more obscure ones might have problems.<br>
If you need to save only mediawiki data and pages modify history then the best and easiest way probably would be:
...
23 KB (3,766 words) - 21:24, 25 August 2023
'''apk''' is the tool used to install, upgrade, or delete software on a running system.<br /
'''lbu''' is the tool used to capture the data necessary to restore a system to a previously configured state.
...
18 KB (2,759 words) - 11:56, 12 January 2024
This page will tell you what requirements you will need to use the Alpine Linux operating system:
...rom personal computers to video game consoles, and as such you must verify the details below:
...
5 KB (725 words) - 04:38, 15 May 2024
To know if you are inside a {{pkg|screen}} session, use the notes in '[[#Get_help|get help]]' section mentioned below.
Lets say you want to attach to a existing session (e.g. the above <code>11131.pts-3.mhlab01</code> session).
...
5 KB (817 words) - 04:17, 28 August 2023
...r is {{ic|not supported}} in the installer script ({{ic|setup-alpine}}) at the moment. If you want to install/extend on more than 1 DASD. However, install
= 2. The boot media =
...
27 KB (3,564 words) - 09:20, 19 January 2024
...dcollect to collect our data for us, we will create all databases that the default config for rrdcollect tries to use.
...conds with which data will be fed into the RRD)'' then make sure to change the 'step' value in /etc/rrdcollect/rrdcollect.conf to reflect your changes abo
...
5 KB (925 words) - 05:28, 6 September 2023
...de>/tmp</code> was part of the root filesystem and was cleaned on boot via the bootmisc openrc service script. In v3.16, new installations will mount <cod
The bootmisc script no longer wipes /tmp on boot. If you want the previous behaviour, set <code>wipe_tmp</code> to YES in /etc/conf.d/bootmis
...
4 KB (593 words) - 02:36, 15 February 2024
...pine_Linux:FAQ| Frequently Asked Questions (FAQ)]], as well as to refer to the official installation guide at [https://docs.alpinelinux.org/ docs.alpineli
...mplete, you will have to figure it out, or ask for the correct solution in the [https://alpinelinux.org/community/ community].
...
23 KB (3,483 words) - 15:53, 4 May 2024
Make sure you have the Flathub repository installed.
After installation Steam can be started using it's .desktop file or on the command line:
...
5 KB (733 words) - 20:00, 9 May 2024