High performance SCST iSCSI Target on Linux software Raid
This is a WIP
Introduction
This HOW-TO is focusing on performance. This is why I made some decisions targeted on performance instead of security (like you are used in Alpine Linux). This means we are not using grsec and not using a firewall. I presume you will take security actions on another level.
To get started, you can download a boot cd here:
http://alpine.nethq.org/distfiles/alpine-scst-110106-x86_64.iso
Content
- Vanilla kernel with SCST (linux-scst)
- Linux software raid and raid level (mdadm)
- Volume Management (LVM2)
- SCST administration (scstadmin)
- Linux raid monitoring
Vanilla Linux kernel with SCST patches
The default Linux kernel will provide support for iSCSI. The biggest issues with this implementation is it operates in userspace. SCST iSCSI will run in kernel and this is one of the reasons why it preforms much better. SCST performance depends on specific patches which need to be applied to the kernel. This is why we created a separate kernel just for SCST usage. SCST modules are already included by default so there is no need for a separate module package to be installed.
P.S. We only provide an x86_64 kernel for SCST because it will perform better on 64bit systems.
Linux software raid
In my personal setup i have 4 pieces of WD RE4 1TB drives which i want to use in the best performance raid level with redundancy. According to many mailing lists and opinion of the Linux raid author RAID10 with layout f2 (far) seems to preform best while still having redundancy. Please remember with RAID10 50% of your hard disk space will go to redundancy, but performance is almost the same as RAID0 (stripe).
For most up-to-date information regarding Linux software raid: https://raid.wiki.kernel.org/index.php/Overview
RAID10 has multiple layout types. f(far)2 in tests seem to preform the best. Please see above link for references.
mdadm -v --create /dev/md0 --level=raid10 --layout=f2 --raid-devices=4 /dev/sda /dev/sdb /dev/sdc /dev/sdd
I am not using partitions on my disks, although there are reasons to use partitions, see here:
https://raid.wiki.kernel.org/index.php/Partition_Types
You can now monitor your raid (re)building: cat /proc/mdstat
By default, the rebuild speed will be set and can be checked and changed here:
cat /proc/sys/dev/raid/speed_limit_max cat /proc/sys/dev/raid/speed_limit_min
make sure we have raid10 module loaded at boot
echo raid10 >> /etc/modules
When you are happy with your raid configuration, save its information to mdamd.conf file
mdadm --detail --scan >> /etc/mdadm.conf
It should display something like
ARRAY /dev/md0 metadata=1.2 name=scst:0 UUID=71fc93b8:3fef0057:9f5feec1:7d9e57e8
When you are ready with your raid setup and its functioning, you will need to make sure its starting at boot time
rc-update add mdadm-raid default
Monitor software raid
Linux software raid can be monitored with mdadm daemon option. Alpine Linux includes an initd script which can invoke the daemon
/etc/init.d/mdadm
It will be default monitor the array's defined in mdadm.conf. To receive email notifications about array issues, we need to provide our email address inside mdadm.conf:
MAILADDR me@inter.net
Because mdadm cannot send email itself, we need to setup an sendmail (replacement) program.
apk add ssmtp
Ssmtp can be configured by editing /etc/ssmtp/ssmtp.conf
You can monitor messages (syslog) for actions invoked by mmdadm.
If you have your own monitoring system active, you can also let mdadm issue a script and notify it.
SCST and iSCSI management
When starting with SCST management we need to have the SCST framework (kernel module) and the iSCSI kernel module loaded
modprobe scst iscsi_scst
After these are loaded we can start the iSCSI deamon
/etc/init.d/iscsi-scst start
This command will return some information based on the current configuration located in: /etc/scst.conf
The basic config when only having iSCSI loaded is:
TARGET_DRIVER iscsi { enabled 0 }
We start add adding a target to the correct target driver
scstadmin -add_target iqn.2010-12.org.alpinelinux:tgt -driver iscsi
The config at this point should be:
TARGET_DRIVER iscsi { enabled 0 TARGET iqn.2010-12.org.alpinelinux:tgt { enabled 0 } }
To add an device
scstadmin -open_dev disk01 -handler vdisk_fileio -attributes filename=/mnt/array1/disk01,nv_cache=1
To close a device
scstadmin -close_dev disk01 -handler vdisk_fileio