|
|
| (21 intermediate revisions by 6 users not shown) |
| Line 1: |
Line 1: |
| == Copy Alpine to a {{{1|Flash Medium}}} ==
| | {{Delete|This redirect is to an include that is obsolete and is completely unused on the wiki}} |
| | |
| # Insert the removable {{{1|flash medium (CF or USB stick)}}} into the computer.
| |
| # Determine the name your computer uses for your {{{1|flash medium}}}. The following step is one way to do this.
| |
| #* After inserting the {{{1|flash medium}}}, run the command:
| |
| #* {{Cmd|dmesg}}
| |
| #* At the end of this command you should see the name of your {{{1|flash medium}}}, likely starting with "sd". (For example: "sda").
| |
| #* The remainder of this document will assume that your {{{1|flash medium}}} is called /dev/sda
| |
| | |
| {{Warning|Be very careful about this. You do not want to mistakenly wipe your hard drive if it's on /dev/sda}}
| |
| | |
| === Format {{{1|Flash Medium}}} ===
| |
| {{Cmd|fdisk /dev/sda}}
| |
| * '''p''' Print list of partitions
| |
| * '''d''' Delete all partitions (this may take a few steps)
| |
| * '''n''' Create a new partition
| |
| * '''p''' A primary partition
| |
| * '''1''' Partition number 1
| |
| ** Use defaults for first and last cylinder (just press [Enter] twice).
| |
| * '''t''' Change partition type
| |
| * '''c''' Type: Win95 FAT32 (LBA)
| |
| * '''a''' <big>Make the partition bootable (set boot flag)</big>
| |
| * '''1''' Partition number 1
| |
| * '''w''' Write your changes to the device
| |
| | |
| === Install Syslinux ===
| |
| {{Note|If the following commands fail due to 'No such file or directory', you may have to remove and reinsert the CF card, or even reboot, to get /dev/sda1 to appear}}
| |
| # Install syslinux and dosfstools. If you have booted from an Alpine CD-ROM, use these commands:
| |
| #* {{Cmd|apk add syslinux dosfstools}}
| |
| #* {{Cmd|{{{|dd if=/usr/share/syslinux/mbr.bin of=/dev/sda}}}}}
| |
| # Format the {{{1|flash medium}}} with a VFAT filesystem:
| |
| #* {{Cmd|mkdosfs -F32 /dev/sda1}}
| |
| #* {{Cmd|syslinux /dev/sda1}}
| |
| #* {{Cmd|mkdir -p /media/sda1}}
| |
| #* {{Cmd|mount -t vfat /dev/sda1 /media/sda1}}
| |
| # Mount the Alpine Linux CD-ROM, and copy the files to the {{{1|flash medium}}}
| |
| #* {{Cmd|mount /media/cdrom}}
| |
| #* {{Cmd|cd /media/cdrom}}
| |
| #* {{Cmd|cp -a .alpine-release * /media/sda1/ }}
| |
| | |
| == Troubleshooting ==
| |
| When your USB device is formatted to other filesystem than fat32, you might have to specify the necessary filesystem modules in boot parameters.
| |
| | |
| To do so, mount the device, and alter the syslinux.cfg file line from
| |
| append initrd=/boot/grsec.gz alpine_dev=usbdisk:vfat modules=loop,cramfs,sd-mod,usb-storage quiet
| |
| to
| |
| append initrd=/boot/grsec.gz alpine_dev=usbdisk:vfat modules=loop,cramfs,sd-mod,usb-storage,ext3 quiet
| |
| | |
| in case of using ext3 formatted partition. Similar procedure might apply to other filesystems (if they are supported by syslinux or other bootloader of your choice and alpine kernel).
| |
| | |
| Also, specifying waitusb=X option might help with certain usb devices that take a bit longer to register. X stands for the amount of seconds kernel will wait before looking for the installation media.
| |
