User:Mhavela/squark-auth-snmp: Difference between revisions

From Alpine Linux
(Introduction)
(No difference)

Revision as of 05:54, 22 December 2011

This material is work-in-progress ...

Do not follow instructions here until this notice is removed.
(Last edited by Mhavela on 22 Dec 2011.)

Using squark-auth-snmp

Introduction

This document describes how to use 'squark-auth-snmp' as squid authentication helper to obtain a username or other useful information from a switch.
'squark-auth-snmp' queries the switch via SNMP using standard MIBs to obtain various information.
The information is then injected into the squid access logs (which can help auditors when analysing the logs).

Todo: Mention lldp above?


Switches that confirmed to function at least in some degree:

  • HP Procurve 5400zl
  • HP Procurve 1810G 24GE
Todo: Confirm if "HP Procurve 2150-48" works


Todo: Confirm if "HP Procurve 2650" works


Note: For more information see the 'squark-auth-snmp' documentation here (git tree)

Enable SNMP Lookups on HP Procurve Device

Create an SNMP read-only community on your HP Procurve Switch, or use one that already exists (the following example uses "public" as a community name - adjust as you like):

configure snmp-server community "public" restricted snmp-server response-source dst-ip-of-request exit

The 2nd last command ensures that the SNMP replies are always returned from the switch's primary management interface. Run the above commands on all switches that the squark-auth plugin will run snmp queries against. Run them exactly as they appear.

Install Squark and Configure Squid

apk add squark

The squark-auth binary used by squid is copied into the /usr/local/bin directory. All further configuration is done in /etc/squid/squid.conf:

Note: The following configuration assumes that you are using SNMPv2c
#external ACL squid auth helper
# Squark authentication external acl
external_acl_type squark_auth children=1 ttl=1800 negative_ttl=60 concurrency=128 grace=10 %SRC /usr/local/bin/squark-auth -c <communityname> -r <ip.of.switch> -i VLAN<id> -v <id>
acl Zone_D_SquarkAuth external squark_auth

Replace <communityname> with the SNMPv2 community name you have configured on your switch. Replace <ip.of.switch> with the IP of your switch, and replace <id> with the VLAN Id number of the VLAN that the clients will be connected to.

Here is an example to illustrate how the above configuration could look:

#external ACL squid auth helper
# Squark authentication external acl
external_acl_type squark_auth children=1 ttl=1800 negative_ttl=60 concurrency=128 grace=10 %SRC /usr/local/bin/squark-auth -c public -r 192.168.0.1 -i VLAN5 -v 5
acl Zone_D_SquarkAuth external squark_auth
Note: If you have multiple switches in your environment, Link Layer Discovery Protocol (LLDP) should be enabled in order for squark-auth to work properly. If the IP of the switch that you have specified is a core switch (such as in a star topology network, and the all the switches in your network have LLDP enabled (usually enabled by default), then your network topology should be automatically discoverable.
Note: For more information on the squark_auth options available, run the command man squark-auth.

Optional: SNMP v3 Configuration

Squark will use the configuration specified in /etc/snmp/snmp.conf when snmpv3 is specified as the preferred version of SNMP to use.

Ensure that you have at least the following in /etc/snmp/snmp.conf:

defContext none
defSecurityName <username>
defAuthPassphrase <password>
defVersion 3
defAuthType MD5
defSecurityLevel authNoPriv

Adjust the above as dictated by the SNMP v3 configuration on your switch.