Alpine on ARM

From Alpine Linux
Revision as of 18:46, 21 April 2023 by Sb1 (talk | contribs) (→‎Supported SoCs: working bootloader shipped?)
This material needs wiki syntax or style improvements ...

Please feel free to help us clean it up.

This page is proposed for moving ...

It should be renamed to ARM SOCs. (Discuss)

(Parts of this page are still incomplete and might even need corrections.)


Supported SoCs

Alpine gets compiled with support files for so many and even formidable SoCs, beside the Raspberry Pi, that to find out about a particular chipset's support it can be useful to refine the search for all "*.dtb" files in the package database (i.e. filter for "*<some-board-or-SoC-identifying-string>*.dtb" file).

For example, by refining the following search in the current "edge" release:

DTB-files in the current edge branch: https://pkgs.alpinelinux.org/contents?repo=main&file=*.dtb&branch=edge

Fully supported boards are those for which there is a working bootloader shipped in the download.

Installing Alpine on supported Boards

Get latest Alpine image

The latest images are available at: https://alpinelinux.org/downloads/

In case the download page provides no specific image for your particular board, download the "Generic ARM" image.

The *.tar.gz files (aka "tarballs") need to be extracted to some boot media device.

(Useful hints about basic identification of and access to your sdcard or usb target device, may also be found in the general instructions at https://wiki.alpinelinux.org/wiki/Installation.)

After extracting the files onto an usb-stick or sdcard, some devices, typically those using widely used standards, possibly basic boot selection jumpers, or featuring an internal flash chip with a modern bootloader, possibly with boot menu, may allow to boot the media right away.

However, if your device (even with its internal bootloader firmware, if any, updated to the latest version) is not able to boot the media as is, then some specific adjustment of the boot media (according to the requirements of your device) is needed to allow booting.

Preparation of adjusted boot media in general

Here we are using an sdcard and the "Wandboard" as a rather genric example. If your particular board happens to require something to boot Alpine not mentioned here in any more specific documents link below, please consider adding the missing info, e.g. by adding to the links below.

Start by extracting the archive somewhere.

Then install the SoCs particular boot loader(s) to the places on the sdcard where the device expects them, e.g. the SPL and u-boot.img (this differs between boards):

As user root, and from the location of the extracted image files, do a direct disk write using as input file the SPL from the extracted Alpine image, and the sdcard (here /dev/sdX) as output file node (the target device): 

dd if=u-boot/wandboard/SPL of=/dev/sdX seek=1 bs=1k

Similarly, for the u-boot.img: 

dd if=u-boot/wandboard/u-boot.img of=/dev/sdX seek=69 bs=1k

After creating a partition on the sd-card, behind the boot loaders (e.g. with fdisk) and mounting it, copy the folders apks/, boot/, efi/, extlinux/, and u-boot/ to the sd-card partition. (I'm not sure if all folders are needed).

Finally, put the sd-card in the Wandboard and boot it with a serial console connected.

The board should now boot from the sd-card. When the prompt asks for a login, you can follow https://wiki.alpinelinux.org/wiki/Installation to run setup-alpine as usual.

More specific guides

Not fully supported boards

If you have e.g. an armv6/armv7 board that is not fully supported, but whose SoC is already supported by the mainline kernel and uboot, then it's still possible to install Alpine. It may involve a couple more manual steps, though.


Requirements

  • Alpine's forked uboot to support tarballs (fabled?)
  • serial console
  • crosscompiler/toolchain if you can not compile natively


The embedded world

A lot of the SoCs have their own way of doing things, although they use uboot and Linux kernel but often they are heavily modified to suit easy flashing of "ROMs" or other unknown reasons, e.g. Rockchip's notion "partition" are neither DOS nor GPT partitions. Here, we will try to install Alpine in a more standard way, like on the x86 platform, with either DOS or GPT partitions. To boot this, you will most likely have to install/flash the mainline uboot, which can be non-destructive if you can load it from external storage.


Storage

One can load uboot from the following block devices if it's supported.

  • NAND
  • eMMC
  • SD card
  • USB


Power on

Some SoCs need both SPL and uboot, you need to check uboot for your board. Most (if not all) boards boots from the internal storage first (either NAND or eMMC) you will have to check documentation of your board if you wish to boot the SPL/uboot from SD/USB.

One can view SPL+uboot as BIOS and boot-loader on PC. Think that you could put the BIOS on an external storage :D

Once you have loaded the "standard" uboot, things are more or less like on x86.


Partitioning

Either DOS or GPT patitions should work. Start of the first partition should be on block 2048 so there is space for SPL/uboot and marked bootable (with the MBR bootable flag, or GPT legacy_bios_bootable attribute).

  • SPL starts at block 64 (please consult the docs for your board)
  • uboot starts at block 256 (please consult the docs for your board)

Just dd SPL and boot with the correct offset to the media you wish to boot

Booting Linux kernel

  • uboot uses extlinux.conf file to locate the kernel/initramfs/... just like syslinx, you need to put that file on the partitions which is marked bootable in the /boot directory
  • there should be an extra line "FDTDIR" which points to the DTBs

e.g. 

label Fedora (3.17.0-0.rc4.git2.1.fc22.armv7hl) 22 (Rawhide)
	kernel /boot/vmlinuz-3.17.0-0.rc4.git2.1.fc22.armv7hl
	append ro root=UUID=8eac677f-8ea8-4270-8479-d5ddbb797450 console=ttyS0,115200n8 LANG=en_US.UTF-8 drm.debug=0xf
	fdtdir /boot/dtb-3.17.0-0.rc4.git2.1.fc22.armv7hl
	initrd /boot/initramfs-3.17.0-0.rc4.git2.1.fc22.armv7hl.img

Using QEMU

qemu-system-arm -M vexpress-a9 -kernel zImage -initrd initramfs-grsec -dtb vexpress-v2p-ca9.dtb -hda hda.img -serial stdio


References

Retrieved from "https://wiki.alpinelinux.org/w/index.php?title=Alpine_on_ARM&oldid=23263"