Alpine Linux:Overview

From Alpine Linux
Revision as of 13:57, 20 December 2024 by Prabuanand (talk | contribs) (Removed the link and transcluded Include:Architecture support matrix)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

Alpine uses musl as its libc, and BusyBox as core utilities. These choices tend to make Alpine especially minimalist and secure.

General overview

Alpine Linux has one of the fastest boot times of any operating system.

It's famous because of its small size and it's heavily used in containers.

It's also well known for wide use in embedded devices and as a base system for many enterprise routers.

The postmarketOS project, which is designed to run on mobile devices, is based on Alpine Linux.

Distinctive

Alpine Linux follows the principles of the SSS distro: Simple+Small+Secure: due to usage of muslc as the minimalist libc, BusyBox simple coreutils (with possibilities to alternate on inflated original packages of each coreutils tools also) and userland binaries compiled as Position Independent Executables (PIE) with stack smashing protection.

Efficient

Some main reasons:

  1. Usage of musl as the minimalist libc
  2. Its own package manager called apk,
  3. The openrc init system, script driven set-ups and that’s it!
  4. busybox: simple coreutils (with possibilities to alternate on inflated original packages of each coreutils tools also)

This provides you with a simple, crystal-clear Linux environment without all the noise, nothing else will get in the way.

Secure

All userland binaries are compiled as Position Independent Executables (PIE) with stack smashing protection.

Technical overview

  1. Architectures

    Alpine uses Linux as OS kernel, and has a focus on SSS distribution, Simple Small and Secure. The table below represents architectures supported by Alpine Linux:


    Alpine Linux Hardware Support Matrix
    Architecture Port Description Since
    x86 x86 32 bit i686 compatible (or later) CPUs with at least CMOV and SSE2 All
    x86_64 AMD64 compatible 64-bit x86 instruction set All
    ARM armhf 32 bit ARM with hard-float ABI - for ARMv6 devices- Raspberry Pi 1, Zero, ZeroW, cm1 (defconfig bcmrpi) v3.0
    armv7 32 bit ARM - for ARMv7 devices - Raspberry Pi 2, 3, 3+, Zero2W, cm3, cm3+ (defconfig bcm2709) v3.9
    aarch64 64 bit ARM - for ARMv8+ devices - Raspberry Pi 3, 3+, 4, 400, Zero2W, cm3, cm3+, cm4, 5 (defconfig bcm2711) v3.5
    PowerPC ppc64le 64 bit PowerPC (little-endian) mostly for POWER8 and POWER9 v3.6
    IBM System Z s390x IBM Z mainframes, especially IBM Z and IBM LinuxONE (z196 minimum) v3.6
    RISC V riscv64 64 bit RISC V v3.20
    LoongArch loongarch64 64 bit LoongArch v3.21
  2. Installing

    Alpine can be installed to a hard disk/SSD/other storage medium like any other distro (this is called sys mode). The storage medium in question can be any block device (USB, Flash, SDD, HDD). It can be removable, so long as you can configure your machine to boot from it. But if you're working with removable media, you might prefer one of the other installation modes.

    In each of these modes, you boot your machine from a static image. You will also need a writable medium to save updates to the system. In diskless mode, that medium is usually a small USB key (or a partition on one) that holds the changes you want to persist. Both the base Alpine system and all your changes will be unpacked into a memory-based filesystem.

    The other, data mode is for when you're dealing with a large amount of persisting data, that you want to keep on a hard disk/SSD/other storage medium, rather than unpacking into memory. The default setup here is to store your /var partition directly on the hard storage medium. But as in the diskless mode, your root system still comes from a static ISO image.

    These second and third installation modes are sometimes referred to, collectively, as "run-from-RAM" installations.

    Key to these installation modes is Alpine's lbu utility. This tracks which files you've modified from their static ISO version, and want the changes to persist. The lbu utility saves those changes in .apkovl "overlay" files. (These are essentially tar-gzip archives, though they can also be encrypted. You can use the lbu utility with the sys mode, too, if you like: as a form of backup, or to configure overlay files for other systems. But for a robust incremental backup system, you'll probably want a more specialized tool, such as rsnapshot.)

    The lbu utility is part of the alpine-conf package, which is required by alpine-base.


    Alpine's installer consists of the /sbin/setup-* scripts, which are also part of the alpine-conf package.

    A base Alpine install will include only needed packages such like alpine-base, syslinux, linux-lts (or another kernel package), and depending on your purposes packages like openssh and/or chrony.

    Alpine's boot loader in that case is syslinux, or its companions isolinux or extlinux. The latest releases also have Grub and UEFI support.

  3. The init system

    An "init system" includes several different components. First, there is the initramfs, which is loaded by the bootloader. Alpine's tool for generating the initramfs is /sbin/mkinitfs, part of the mkinitfs package, which is required by Alpine's kernel packages and by its syslinux package. This tool's settings are read from /etc/mkinitfs/*, and it installs the initscript /usr/share/mkinitfs/initramfs-init into the initramfs.

    Second, Alpine uses OpenRC to handle the rest of its initscripts. The base framework of this is in the openrc package, which is required by alpine-conf.

  4. The packaging and development system

    The last important distinguishing feature of a Linux distro is its packaging and development systems.

    In Alpine's case, these are something a hybrid between ArchLinux's, on the one hand, and Gentoo and FreeBSD's, on the other. Our package-management and build utilities work much like Arch's:

    What Alpine borrows from Gentoo and FreeBSD is a tree of all the package-building scripts. It is called the Aports tree, and is kept as a single git repository. (Compare Gentoo's "Portage" and FreeBSD's "ports". Something similar can be set up with Arch's "abs", but it's not as tightly integrated with their package manager and build utilities.)

    If you're only planning to install packages on a given system, and not do any development there, then the only pieces of this you'll need are mkinitfs and apk-tools, both included in a base Alpine install. If you do plan to do development, install alpine-sdk, which includes gcc, git, abuild, and the like, and see Developer Documentation.

See Also