PipeWire

This material is work-in-progress ...

The instructions below have not been thoroughly tested and may break things.
(Last edited by Dekedro on 2 Oct 2022.)

PipeWire is a multimedia processing engine that aims to improve audio and video handling on Linux.

Prerequisites

Audio Group

When elogind is not available, the user has to be added to the audio group. The user must re-log-in in for this to take effect.

# addgroup <user> audio

D-Bus

PipeWire requires a running D-Bus session for some of its functionality. If you use a full desktop environment this will probably be started automatically, but with minimal window managers it must be done manually.

# apk add dbus dbus-openrc
# rc-service dbus start
# rc-update add dbus default

Then use dbus-run-session whenever you start an X or Wayland session. For example:

$ dbus-run-session -- sway

For certain configurations (e.g. only audio playback and recording) D-Bus setup is not necessary.

XDG_RUNTIME_DIR

If you are not using a Desktop Manager, ensure that your XDG_RUNTIME_DIR is set to a user-writable location. By default for pulseaudio this is /run/user/1000/ or /tmp. If this is not set, pipewire will create a directory in your home folder instead, called ~/pulse, and on attempting to run Pavucontrol or pactl, you will get the following error:

$ pactl list
Connection failure: Connection refused
pa_context_connect() failed: Connection refused

Installation and configuration

# apk add pipewire wireplumber

Note: Using WirePlumber rather than the pipewire-media-session (which comes with pipewire) is recommended but not required.

Realtime scheduling

For realtime scheduling, it is recommended to use rtkit,

# apk add rtkit

and then add your user to the `rtkit` group.

Alternatively, ensure your user has the right ulimit permissions. You generally need (limits.conf format):

@audio - memlock 256
@audio - nice -11
@audio - rtprio 88

This allows a member of the audio group to have the right permissions for PipeWire to use realtime scheduling without rtkit.

ALSA

# apk add pipewire-alsa

ALSA support works out of the box if you have the pipewire-alsa package. You may need the snd_seq kernel module.

PulseAudio

PipeWire can run a PulseAudio daemon which should allow all existing PulseAudio applications to be used with the PipeWire backend. You need to have pipewire-pulse installed.

JACK

If you will be using PipeWire for JACK applications install the required package (pipewire-jack). Things should work with just that.

Video

Video should work out-of-the-box with v4l2 devices (e.g. a lot of webcams) and GStreamer applications.

Bluetooth audio

Enable PulseAudio support as described above
Install bluetooth service packages: bluez bluez-openrc pipewire-spa-bluez
Optional: install GUI manager for bluetooth blueman
Enable and start bluetooth service: rc-update add bluetooth; rc-service bluetooth start
Restart PipeWire
Use commandline program bluetoothctl or GUI program blueman-manager to scan and pair bluetooth audio devices.
Use pavucontrol to adjust volume and manually select high definition bluetooth codecs.

Screen sharing on Wayland

You will need the right xdg-desktop-portal backend for your desktop environment. Screen sharing is known to work on:

GNOME with xdg-desktop-portal-gtk
KDE Plasma with xdg-desktop-portal-kde and Firefox
Sway with xdg-desktop-portal-wlr and Firefox, see Sway for details

Usage

Start the PipeWire media server. You'll probably get quite a few errors but just ignore them for now.

$ /usr/libexec/pipewire-launcher

Note: PipeWire doesn't auto-start a session manager anymore. In 3.14 and earlier, the PipeWire default config was edited in packaging to auto-start pipewire-media-session as the default session manager. Since we now have wireplumber available as an alternative session manager, this has been changed in favor of a launch wrapper for pipewire at /usr/libexec/pipewire-launcher. When executed, this will launch pipewire, pipewire-media-session or wireplumber, and pipewire-pulse, depending on what modules are available. If you were launching /usr/bin/pipewire and the session manager manually before, please use the new launcher wrapper instead. WirePlumber can now also be used as a proper alternative for pipewire-media-session.

In a different terminal window check the default output device. I don't yet know how this default can be changed for all applications, so you'd better hope it's right!

wireplumber:

$ wpctl status

Test sound is working using an audio file in a format supported by libsndfile (e.g. flac, opus, ogg, wav).

# apk add pipewire-tools
$ pw-cat -p test.flac

If you have a microphone test audio recording is working.

$ pw-cat -r --list-targets
$ pw-cat -r recording.flac
(Speak for a while then stop it with Ctrl+c)
$ pw-cat -p recording.flac

Test PulseAudio clients using a media player (most use PulseAudio) and if you use JACK test that too:

# apk add jack-example-clients
$ jack_simple_client

You should hear a sustained beep.

If you are happy everything is working, make PipeWire start automatically when your X or Wayland session starts. For example, you could add the /usr/libexec/pipewire-launcher command to ~/.xinitrc or your window manager's config file.

Troubleshooting

`wpctl status` shows no targets

First, check whether ALSA knows about your sound card:

aplay -l

If sound devices are found, the issue is with your pipewire configuration. Consider double-checking the instructions above.

Otherwise, your sound card may not be supported in the version of the Linux Kernel you're running. You should search online for fixes relating to your current kernel version and the codec of your sound card. You can find each of these with:

uname -r
cat /proc/asound/card0/codec* | grep Codec

Quick Configuration

You might want to use pavucontrol to have a simple GUI app for controlling sound, outputs, etc, in which case:

# apk add pavucontrol