Enable Serial Console on Boot

From Alpine Linux
Revision as of 02:53, 30 July 2022 by Yjftsjthsd-a (talk | contribs) (document using serial console with qemu)

Syslinux / Extlinux

How to Enable the Serial Console on Boot (1.10.x)

When using syslinux to boot, you'll need to modify the syslinux.cfg file in the root directory of the boot device. If using a disk-based Alpine, modify the /boot/extlinux.cfg file.

Add the following:

  • serial 0 9600
  • add console=ttyS0,9600 to the append parameter
  • optionally, remove quiet from the append parameter

Example syslinux.cfg

serial 0 9600
timeout 20
prompt 1
default grsec
label grsec
        kernel /boot/grsec
        append initrd=/boot/grsec.gz alpine_dev=sda1:vfat modules=sd-mod,usb-storage console=ttyS0,9600


extlinux.conf (3.0+)

The /etc/update-extlinux.conf is read by the update-extlinux utility.

To do so, change the default entry: 

default_kernel_opts="quiet"

to read like this: 

default_kernel_opts="console=ttyS0,9600 quiet"

Set the serial port and baud rate to match the default_kernel_opts line above: 

serial_port=0
serial_baud=9600

Xen

Notice, if you want to use this for a Xen VM, you need to configure the speed at 115200 bps and enable the 

serial="pty"

setting in the VM config file.

Xen can be configured to use and log to a serial console by editing /etc/update-extlinux.conf to include the following lines: 

default_kernel_opts="console=hvc0 earlyprintk=xen nomodeset"
xen_opts="dom0_mem=256M com1=115200,8n1 console=com1"

See the Xen wiki for more details.

qemu

Like Xen, qemu should run at speed 115200.

Conveniently, the alpine "virt" image (but not the "standard" image) comes with this all configured on the default ISO.

Sample command to run qemu on alpine-virt with a serial console: 

qemu-system-x86_64 -accel kvm -cdrom alpine-virt-3.16.0-x86_64.iso -display none -chardev stdio,id=char0,logfile=serial.log,signal=off -serial chardev:char0

Note that this example command uses the logfile option to log the output of the serial console; you can remove this if you don't need it.

Example /boot/extlinux.conf

This is a complete file, written by the update-extlinux command. 

DEFAULT menu.c32
PROMPT 0
MENU TITLE Alpine/Linux Boot Menu
MENU AUTOBOOT Alpine will be booted automatically in # seconds.
SERIAL 0 9600
TIMEOUT 100
LABEL grsec
  MENU DEFAULT
  MENU LABEL Linux 3.10.33-0-grsec
  LINUX vmlinuz-3.10.33-0-grsec
  INITRD initramfs-3.10.33-0-grsec
  APPEND root=UUID=re-mov-ed-uu-id modules=sd-mod,usb-storage,ext4 console=ttyS0,9600

MENU SEPARATOR

Please: adjust the tty speed to 115200 if needed (Xen/qemu!!).

The timeout is given in deciseconds, so this would be a 10 second timeout.[1] A timeout of 0 does not boot without delay, but rather waits indefinitely for the user.

If the file is read by pygrub, the same value is interpreted as seconds, resulting in a 100s bootup delay per VM.

Grub

If you're using Grub as your bootloader, follow this section. Edit /etc/default/grub and add the following lines (assuming you're using the first serial port at 115200 baud rate): 

GRUB_TERMINAL="serial console"
GRUB_SERIAL_COMMAND="serial --unit=0 --word=8 --parity=no --speed 115200 --stop=1"

Also add console=ttyS0,115200n8d to the GRUB_CMDLINE_LINUX_DEFAULT variable

Your /etc/default/grub should now look something like this: 

GRUB_TIMEOUT=2
GRUB_DISABLE_SUBMENU=y
GRUB_DISABLE_RECOVERY=true
GRUB_CMDLINE_LINUX_DEFAULT="console=tty0 console=ttyS0,115200n8d modules=sd-mod,usb-storage,xfs quiet rootfstype=xfs"
GRUB_TERMINAL="serial console"
GRUB_SERIAL_COMMAND="serial --unit=0 --word=8 --parity=no --speed 115200 --stop=1"

Now, regenerate your grub.cfg with the following command: 

grub-mkconfig -o /boot/grub/grub.cfg

Follow the final 2 steps below: Enabling a login console and Add your serial console to the trusted local terminal list

Enabling a login console

This is done in /etc/inittab. There is commented entry for ttyS0. Just enable it. 

# Put a getty on the serial port
ttyS0::respawn:/sbin/getty -L ttyS0 115200 vt100

To start the getty, restart init: 

kill -HUP 1

Enabling two consoles during boot

It's possible to output to both the serial and vga console during the system boot. 

append "quiet console=ttyS0,9600 console=tty0"

Not known how to do the same thing in the extlinux menu. You might find a starting point in this thread: http://patchwork.openembedded.org/patch/45175/

Add your serial console to the trusted local terminal list

If you face the problem that the login prompt always refuses your password when you use serial console, you missed this entry.

Add this to the /etc/securetty file: 

ttyS0
Retrieved from "https://wiki.alpinelinux.org/w/index.php?title=Enable_Serial_Console_on_Boot&oldid=22154"