PipeWire

This material is work-in-progress ...

The instructions below have not been thoroughly tested and may break things.
(Last edited by Katt0 on 12 Feb 2022.)

PipeWire is a multimedia processing engine that aims to improve audio and video handling on Linux.

Prerequisites

Audio Group

When elogind is not available, the user has to be added to the audio group. The user must log in for this to take effect.

# addgroup <user> audio

D-Bus

PipeWire requires a running D-Bus session. If you use a full desktop environment this will probably be started automatically, but with minimal window managers it must be done manually.

# apk add dbus dbus-openrc dbus-x11
# rc-service dbus start
# rc-update add dbus default

Then use dbus-launch whenever you start an X or Wayland session. For example:

$ dbus-launch --exit-with-session sway

XDG_RUNTIME_DIR

If you are not using a Desktop Manager, ensure that your XDG_RUNTIME_DIR is set to a user-writable location. By default for pulseaudio this is /run/user/1000/ or /tmp. If this is not set, pipewire will create a directory in your home folder instead, called ~/pulse, and on attempting to run Pavucontrol or pactl, you will get the following error:

$ pactl list
Connection failure: Connection refused
pa_context_connect() failed: Connection refused

Installation and configuration

# apk add pipewire wireplumber rtkit

Note: Using WirePlumber rather than the pipewire-media-session (which comes with pipewire) is recommended but not required.

Create a custom configuration file in /etc/pipewire/pipewire.conf:

# mkdir /etc/pipewire
# cp /usr/share/pipewire/pipewire.conf /etc/pipewire/

Add the following line to the context.exec section at the bottom of /etc/pipewire/pipewire.conf:

{ path = "wireplumber"  args = "" }

Enable the snd_seq kernel module for ALSA support.

# modprobe snd_seq
# echo snd_seq >> /etc/modules

Now, edit /usr/share/polkit-1/actions/org.freedesktop.RealtimeKit1.policy and change the <allow_any> on line 14 to yes instead of no, and do the same for line 26

ALSA

If you use neither Jack nor PulseAudio and you don't intend to.

# touch /etc/pipewire/media-session.d/with-alsa

PulseAudio

PipeWire can run a PulseAudio daemon which should allow all existing PulseAudio applications to be used with the PipeWire backend.

# apk add pipewire-pulse

Uncomment the following line in /etc/pipewire/pipewire.conf:

{ path = "/usr/bin/pipewire" args = "-c pipewire-pulse.conf" }

It should be automatically enabled.

JACK

If you will be using PipeWire for JACK applications install the required package and make system wide links to the PipeWire replacement JACK libraries (I have not had success using pw-jack). You will not need to start a JACK server.

# apk add pipewire-jack
# ln -sf /usr/lib/pipewire-0.3/jack/libjackserver.so.0 /usr/lib/libjackserver.so.0
# ln -sf /usr/lib/pipewire-0.3/jack/libjacknet.so.0 /usr/lib/libjacknet.so.0
# ln -sf /usr/lib/pipewire-0.3/jack/libjack.so.0 /usr/lib/libjack.so.0

Note: These symlinks might be overwritten during updates.

Video

Video should work out-of-the-box with v4l2 devices (e.g. a lot of webcams) and GStreamer applications.

Bluetooth headset

Requires pipewire-spa-bluez package in addition to pipewire-pulse daemon to be installed.

Automatic bluetooth profile selection

To automatically switch between HSP/HFP and A2DP profiles when an input stream is detected, set the bluez5.autoswitch-profile property to true:

/etc/pipewire/media-session.d/bluez-monitor.conf

...
rules = [
    {
        ...
        actions = {
            update-props = {
                ...
                bluez5.autoswitch-profile = true
...

Screen sharing on Wayland

You will need the right xdg-desktop-portal backend for your desktop environment. Screen sharing is known to work on:

GNOME with xdg-desktop-portal-gtk
KDE Plasma with xdg-desktop-portal-kde and Firefox
Sway with xdg-desktop-portal-wlr and Firefox

Usage

Start the PipeWire media server. You'll probably get quite a few errors but just ignore them for now.

$ pipewire

Note: PipeWire doesn't auto-start a session manager anymore. In 3.14 and earlier, the PipeWire default config was edited in packaging to auto-start pipewire-media-session as the default session manager. Since we now have wireplumber available as an alternative session manager, this has been changed in favor of a launch wrapper for pipewire at /usr/libexec/pipewire-launcher. When executed, this will launch pipewire, pipewire-media-session or wireplumber, and pipewire-pulse, depending on what modules are available. If you were launching /usr/bin/pipewire and the session manager manually before, please use the new launcher wrapper instead. WirePlumber can now also be used as a proper alternative for pipewire-media-session.

In a different terminal window check the default output device. I don't yet know how this default can be changed for all applications, so you'd better hope it's right!

# apk add pipewire-tools
$ pw-cat -p --list-targets

Test sound is working using an audio file in a format supported by libsndfile (e.g. flac, opus, ogg, wav).

$ pw-cat -p test.flac

If you have a microphone test audio recording is working.

$ pw-cat -r --list-targets
$ pw-cat -r recording.flac
(Speak for a while then stop it with Ctrl+c)
$ pw-cat -p recording.flac

Test PulseAudio clients using a media player (most use PulseAudio) and if you use JACK test that too:

# apk add jack-example-clients
$ jack_simple_client

You should hear a sustained beep.

If you are happy everything is working, make PipeWire start automatically when your X or Wayland session starts. For example, you could add the pipewire command to ~/.xinitrc or your window manager's config file.

Troubleshooting

`pw-cat -p --list-targets` shows no targets

First, check whether ALSA knows about your sound card:

aplay -l

If sound devices are found, the issue is with your pipewire configuration. Consider double-checking the instructions above.

Otherwise, your sound card may not be supported in the version of the Linux Kernel you're running. You should search online for fixes relating to your current kernel version and the codec of your sound card. You can find each of these with:

uname -r
cat /proc/asound/card0/codec* | grep Codec