Template:Copying Alpine to Flash: Difference between revisions

Revision as of 09:21, 8 February 2011

Copy Alpine to a Flash Medium

Insert the removable flash medium (CF or USB stick) into the computer.
Determine the name your computer uses for your flash medium. The following step is one way to do this.
- After inserting the flash medium, run the command:
- dmesg
- At the end of this command you should see the name of your flash medium, likely starting with "sd". (For example: "sda").
- The remainder of this document will assume that your flash medium is called /dev/sda

Warning: Be very careful about this. You do not want to mistakenly wipe your hard drive if it's on /dev/sda

Format Flash Medium

fdisk /dev/sda

p Print list of partitions
d Delete all partitions (this may take a few steps)
n Create a new partition
p A primary partition
1 Partition number 1
- Use defaults for first and last cylinder (just press [Enter] twice).
t Change partition type
c Type: Win95 FAT32 (LBA)
a Make the partition bootable (set boot flag)
1 Partition number 1
w Write your changes to the device

Install Syslinux

Note: If the following commands fail due to 'No such file or directory', you may have to remove and reinsert the CF card, or even reboot, to get /dev/sda1 to appear

Install syslinux and dosfstools. If you have booted from an Alpine CD-ROM, use these commands:
- apk add syslinux dosfstools
- dd if=/usr/share/syslinux/mbr.bin of=/dev/sda
Format the flash medium with a VFAT filesystem:
- mkdosfs -F32 /dev/sda1
- syslinux /dev/sda1
- mkdir -p /media/sda1
- mount -t vfat /dev/sda1 /media/sda1
Mount the Alpine Linux CD-ROM, and copy the files to the flash medium
- mount /media/cdrom
- cd /media/cdrom
- cp -a .alpine-release * /media/sda1/

Troubleshooting

When your USB device is formatted to other filesystem than fat32, you might have to specify the necessary filesystem modules in boot parameters.

To do so, mount the device, and alter the syslinux.cfg file line from

append initrd=/boot/grsec.gz alpine_dev=usbdisk:vfat modules=loop,cramfs,sd-mod,usb-storage quiet

to

append initrd=/boot/grsec.gz alpine_dev=usbdisk:vfat modules=loop,cramfs,sd-mod,usb-storage,ext3 quiet

in case of using ext3 formatted partition. Similar procedure might apply to other filesystems (if they are supported by syslinux or other bootloader of your choice and alpine kernel).

Also, specifying waitusb=X option might help with certain usb devices that take a bit longer to register. X stands for the amount of seconds kernel will wait before looking for the installation media.

@@ Line 38: / Line 38: @@
 #* {{Cmd|cd /media/cdrom}}
 #* {{Cmd|cp -a .alpine-release * /media/sda1/ }}
-=== Set up a Serial Console (Optional) ===
-You can now edit syslinux.cfg to add a serial console to the {{{1|flash medium}}}.
-# Open /media/sda1/syslinux.cfg for editing.
-#* {{Cmd|vi /media/sda1/syslinux.cfg}}
-# Add the line `serial 0 9600` to the top of the file
-# Add the text ` console=tty1,38400 console=ttyS0,9600` to the end of the "append" line.
-The result should look like this:
- serial 0 9600
- timeout 20
- prompt 1
- default grsec
- label grsec
- 	kernel /boot/grsec
- 	append initrd=/boot/grsec.gz alpine_dev=usbdisk:vfat modules=loop,cramfs,sd-mod,usb-storage console=tty1,38400 console=ttyS0,9600
-Next, enable the serial console on ttyS0 by editing the inittab file:
-# Open /media/sda1/etc/inittab for editing.
-#* {{Cmd|vi /media/sda1/etc/inittab}}
-# Find and uncomment the following line:
-#: <pre>#ttyS0::respawn:/sbin/getty -L ttyS0 9600 vt100</pre>
-#: So it looks like this:
-#: <pre>ttyS0::respawn:/sbin/getty -L ttyS0 9600 vt100</pre>
 == Troubleshooting ==