User:Mhavela

Monitor traffic using Snort and bridged nics

Prepare

Hardware

Hardware used in this example:

• Computer with 1 nic
• Switch that handles vlan
• A computer that would be analyzed

Setup analyzer/snort box

Sets up standard settings - But skip nic-settings

setup-alpine

Sets up and start webconf

setup-webconf

Install needed packages

apk_add bridge-utils
apk_add acf-snort

Because we will use vlan's in this example, we need to install vlan support

modprobe 8021q

Switch setup

We need to configure vlans on the ports

• Port X = Untagged=vlan1
• Port Y = Untagged=vlan1, Tagged=vlan2
• Port Z = Untagged=vlan2

Attach equipment into each port

• Port X = Gateway for the 'infected' box
• Port Y = Analyzer/Snort box
• Port Z = The 'infected' box

Configure

Configure bridge. /etc/conf.d/bridge would look like this:

BRIDGES="br0=eth0+eth0.2"

Add vlan2 to nic

vconfig add eth0 2

In our case we have a dhcp running on the system, so we configure br0 to get a lease (edit /etc/network/interfaces file)

auto br0
iface br0 inet dhcp

Start bridge

/etc/init.d/bridge start

Bring up bridge

ifup br0

Start snort

/etc/init.d/snort start

Use 'Huawei E220' HSDPA modem with Alpine

Note: Don't plug in the modem yet
Notes are based on gentoo wiki
To make this work, you will need 'libusb-dev', so you would need Alpine-1.7.21 (or later)

Initial checks

Doing some preparations before starting

apk_add usbutils
lsusb -v > /root/lsusb.org
dmsesg > /root/dmesg.org
ls -1 /dev > /root/ls.dev.org

Note: This step might not be needed in the future (it's here while trying to figure out how this thing works)

Lets check how the kernel is configured

modprobe configs
zcat /proc/config.gz | grep "CONFIG_USB_SERIAL_GENERIC="
zcat /proc/config.gz | grep "CONFIG_USB_SERIAL_OPTION="
zcat /proc/config.gz | grep "CONFIG_PPP="
zcat /proc/config.gz | grep "CONFIG_PPP_ASYNC="

As I understand, all above checks should result in '=m' values.
If not, kernel should be recompiled.
Gentoo wiki saids: "The USB Generic Serial Driver should be disabled altogether.".
Might be CONFIG_USB_SERIAL_GENERIC should be '=y' (but I'm not sure about that)

Congigure modem

Now lets plug in the modem and do some checks

lsusb -v > /root/lsusb.new
diff /root/lsusb.org /root/lsusb.new > /root/lsusb.diff
grep id /root/lsusb.diff

apk_add libusb-dev
modprobe usbserial vendor=0x12d1 product=0x1003
ls -1 /dev > /root/ls.dev.new
diff /root/ls.dev.org /root/ls.dev.new | grep '^+'

Note: At this moment I don't know howto make the above 'modprobe' action to be done automatically at next reboot.

Configure software

Install programs

apk_add ppp
mkdir -p /etc/ppp/peers

Create configfiles

/etc/ppp/peers/E220

/dev/ttyUSB0
460800
crtscts
modem
noauth
usepeerdns
defaultroute
noipdefault
debug
noccp
nobsdcomp
novj
user "irrelevant"
password "irrelevant"
connect '/usr/sbin/chat -f /etc/ppp/chat-E220-pin || /usr/sbin/chat -f /etc/ppp/chat-E220-nopin'

/etc/ppp/chat-E220-pin

ABORT BUSY
ABORT ERROR
ABORT 'NO CARRIER'
REPORT CONNECT
TIMEOUT 10
"" "ATZ"
OK "AT+CPIN=pin"
OK AT+CGDCONT=1,"ip","internet"
OK "ATE1V1&D2&C1S0=0+IFC=2,2"
OK "AT+IPR=115200"
OK "ATE1"
TIMEOUT 60
"" "ATD*99***1#"
CONNECT \c

/etc/ppp/chat-E220-nopin

ABORT BUSY
ABORT ERROR
ABORT 'NO CARRIER'
REPORT CONNECT
TIMEOUT 10
"" "ATZ"
OK AT+CGDCONT=1,"ip","internet"
OK "ATE1V1&D2&C1S0=0+IFC=2,2"
OK "AT+IPR=115200"
OK "ATE1"
 TIMEOUT 60
 "" "ATD*99***1#"
 CONNECT \c

Note: The above highlighted word(s) 'pin' is the PIN of your card (typically a four digit code)
Note: The above highlighted word(s) 'internet' is the Access Point Name (APN) of the service you use (for instance mine is "web.omnitel.it"). If you don't know the Internet APN, ask your service provider.

Test connection

Start connection

pon E220

Stop connection

poff E220