ISCSI Raid and Clustered File Systems: Difference between revisions

Latest revision as of 10:20, 17 November 2023

This material is obsolete ...

SCST is deprecated since Alpine 2.6 in favor of TCM and OCFS2 isn't available in Alpine 3.6 (Discuss)

This document describes how to created a raided file system that is exported to multiple host via ISCSI.

Raid Configuration

Very Similar to Setting up a software RAID array.

apk install mdadm

mdadm --create --level=5 --raid-devices=3 /dev/md0 /dev/hda /dev/hdb /dev/hdc

To see the status of the creation of these devices

cat /proc/mdstat

You Don't have to wait to continue to use the disk.

iSCSI Target Config

SCST is recommended over IET, due to bugfixes, performance and RFC compliance.

Initiator Config

iscsiadm --mode node --targetname NAME_OF_TARGET --portal IP_OF_TARGET --login

This should then give you a device /dev/sda. Check by dmesg.

fdisk /dev/sda

Create a partition to use. sda1 file system type 83

Add ocfs2 tools (available in Alpine 2.3 or greater)

apk add ocfs2-tools

It can take care of starting and stopping services, copying the cluster.conf between nodes,creating the filesystem, and mounting it.

Need to create a /etc/ocfs2/cluster.conf.

This configuration file should be the same on all the nodes in the cluster. Should look similar to the following...

node:

       ip_port = 7777
       ip_address = 192.168.1.202
       number = 0
       name = bubba
       cluster = ocfs2

node:

       ip_port = 7777
       ip_address = 192.168.1.102
       number = 1
       name = bobo
       cluster = ocfs2

cluster:

       node_count = 2
       name = ocfs2

Load modules:

echo ocfs2 >> /etc/modules-load.d/ocfs2.conf
echo dlm >> /etc/modules-load.d/dlm.conf

modprobe ocfs2
modprobe dlm

Mount ocfs2 metafilesystems

echo none /sys/kernel/config configfs defaults 0 0 >> /etc/fstab
echo none /sys/kernel/dlm ocfs2_dlmfs defaults 0 0 >> /etc/fstab

Start ocfs2 cluster

rc-service o2cb start

Run the following command only on one node.

mkfs.ocfs2 -L LABELNAME /dev/sda1

Run the following command on both nodes.

rc-service o2cb enable

mount /dev/sda1 /media/iscsi1

Now you can create read/write/change on both machines to the one drive at the same time.

@@ Line 1: / Line 1: @@
+{{Obsolete|SCST is deprecated since Alpine 2.6 in favor of [[Linux_iSCSI_Target_(TCM)|TCM]] and OCFS2 isn't available in Alpine 3.6}}
 This document describes how to created a raided file system that is exported to multiple host via ISCSI.
 == Raid Configuration ==
-Very Similar to [[Setting_up_a_software_raid1_array]].
+Very Similar to [[Setting up a software RAID array]].
   apk install mdadm
@@ Line 17: / Line 19: @@
 == iSCSI Target Config ==
-[http://scst.sourceforge.net/target_iscsi.html SCST] is recommended over [http://iscsitarget.sourceforge.net/ IET], due to bugfixes, performance and RFC compliance.
+[https://scst.sourceforge.net/target_iscsi.html SCST] is recommended over [https://iscsitarget.sourceforge.net/ IET], due to bugfixes, performance and RFC compliance.
-For a detailed config how-to please look at [[High_performance_SCST_iSCSI_Target_on_Linux_software_Raid]]
 == Initiator Config ==
@@ Line 30: / Line 31: @@
 Create a partition to use. sda1 file system type 83
-Add ocfs2 tools (currently in edge/main)
+Add ocfs2 tools (available in Alpine 2.3 or greater)
   apk add ocfs2-tools
@@ Line 60: / Line 61: @@
 Load modules:
-  echo ocfs2 >> /etc/modules
+  echo ocfs2 >> /etc/modules-load.d/ocfs2.conf
-  echo dlm >> /etc/modules
+  echo dlm >> /etc/modules-load.d/dlm.conf
   modprobe ocfs2
@@ Line 73: / Line 74: @@
 Start ocfs2 cluster
-  /etc/init.d/o2cb start
+  rc-service o2cb start
 Run the following command only on one node.
@@ Line 81: / Line 82: @@
 Run the following command on both nodes.
-  /etc/init.d/o2cb enable
+  rc-service o2cb enable
   mount /dev/sda1 /media/iscsi1
 Now you can create read/write/change on both machines to the one drive at the same time.
+[[Category:Storage]]