Architecture: Difference between revisions
Prabuanand (talk | contribs) m (fixed wikitable with rowspan option) |
Prabuanand (talk | contribs) m (Removed Architectures Category so that it lists only architectures as sub-category) |
||
| (8 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
{{TOC right}} | {{TOC right}} | ||
This page | This page provides brief information on components that make up Alpine Linux. Refer [[Alpine_Linux:Overview|wiki overview]] page for more details. | ||
== Architectures supported == | == Architectures supported == | ||
{ | {{:Include:Architecture support matrix}} | ||
<!-- | <!-- | ||
| Line 73: | Line 51: | ||
== Boot Process == | == Boot Process == | ||
{{Todo|The following section need a clean up with proper wikilinks}} | |||
=== Boot Loader === | === Boot Loader === | ||
| Line 126: | Line 105: | ||
==== Minimal Required Set ==== | ==== Minimal Required Set ==== | ||
{{todo|{{path|/media}} is not required even | |||
{{todo|{{path|/media}} is not required even though it is included in the {{pkg|alpine-baselayout}}}} | |||
===== Directory Structure ===== | ===== Directory Structure ===== | ||
| Line 157: | Line 137: | ||
==== Loading of Kernel Modules ==== | ==== Loading of Kernel Modules ==== | ||
<code>/etc/init.d/modules</code> loads all modules specified in <code>/etc/modules</code> and <code>/(etc|run|usr/lib|lib)/modules-load.d/*.conf</code> | <code>/etc/init.d/modules</code> loads all modules specified in <code>/etc/modules</code> and <code>/(etc|run|usr/lib|lib)/modules-load.d/*.conf</code> | ||
== See also== | |||
[[Category:Hardware]] | [[Category:Hardware]] | ||
Latest revision as of 14:08, 20 December 2024
This page provides brief information on components that make up Alpine Linux. Refer wiki overview page for more details.
Architectures supported
| Alpine Linux Hardware Support Matrix | |||
| Architecture | Port | Description | Since |
|---|---|---|---|
| x86 | x86 | 32 bit i686 compatible (or later) CPUs with at least CMOV and SSE2 | All |
| x86_64 | AMD64 compatible 64-bit x86 instruction set | All | |
| ARM | armhf | 32 bit ARM with hard-float ABI - for ARMv6 devices- Raspberry Pi 1, Zero, ZeroW, cm1 (defconfig bcmrpi) | v3.0 |
| armv7 | 32 bit ARM - for ARMv7 devices - Raspberry Pi 2, 3, 3+, Zero2W, cm3, cm3+ (defconfig bcm2709) | v3.9 | |
| aarch64 | 64 bit ARM - for ARMv8+ devices - Raspberry Pi 3, 3+, 4, 400, Zero2W, cm3, cm3+, cm4, 5 (defconfig bcm2711) | v3.5 | |
| PowerPC | ppc64le | 64 bit PowerPC (little-endian) mostly for POWER8 and POWER9 | v3.6 |
| IBM System Z | s390x | IBM Z mainframes, especially IBM Z and IBM LinuxONE (z196 minimum) | v3.6 |
| RISC V | riscv64 | 64 bit RISC V | v3.20 |
| LoongArch | loongarch64 | 64 bit LoongArch | v3.21 |
Alpine Packaging
Package Building
Alpine Package Building Ports
Package Building Tools
Package Format
Alpine uses packages in the .apk file format.
Package Management Tools
Boot Process
Boot Loader
The Bootloader is responsible for finding the initfs, cmdline and kernel, and handling execution over to the kernel.
Some bootloaders allow the user to interactively pick which OS or kernel to use (if more than one is available).
EFI
- The default setup uses GRUB2.
- See also UEFI Secure Boot
BIOS
- The default setup uses GRUB2.
Other
Kernel
Versioning
Flavors
- lts - long-term support kernel, general purpose
- virt - for running under virtual machines
- edge - Latest stable kernel
- rpi - Raspberry Pi
- rpi2 - Raspberry Pi 2 (Alpine ≤v3.18 only, merged with rpi in current versions)
- rpi4 - Raspberry Pi 4 (Alpine ≤v3.18 only, merged with rpi in current versions)
- ashai - Apple M1
Signing
Command line options
- modules="<modules>" - specify list of modules to be loaded by initramfs /init needed to mount real root filesystem.
Initfs
The kernel will decompress the stream of compressed cpio archives passed to it by the 'append' bootloader option to the root of 'rootfs', a tmpfs automatically mounted at '/' by the kernel at boot.
'/init' Script
Not to be confused with /sbin/init(see below)
This script is in the root of the initfs filesystem and is called by the kernel upon completion of its boot process. It is responsible for doing whatever steps are necessary to mount the real root file system to / and hand over control to /sbin/init.
- Parses kernel command line options.
- Uses nlplug-findfs to discover devices.
- [Optionally] prompts for disk encryption secrets and unlocked encrypted partitions.
Initfs Module Handling
Modules required to mount the root filesystem and boot must either built into the kernel or available from with the initramfs filesystem through use of appended initrd cpio.gz files provided by the bootloader.
The /init script will first modprobe the modules specified by the modules= kernel command line option and by the name of the specified rootfs type. It will then load the contents of /etc/modules, which may include module options. Modules may be blacklisted from autoprobing (but NOT explicit insertion!) using the blacklist= kernel command line option which appends blacklist entries to '/etc/modprobe.d/boot-opt-blacklist.conf'.
Minimal Required Set
Directory Structure
- / /bin /boot /dev /etc /lib /lib/modules /media /media/cdrom /media/usb /mnt /proc /sbin /sys /usr /usr/bin /usr/sbin
Devices
- /dev/null
- /dev/console
- /dev/kmsg
Mounts
- /proc
- /sys
- /dev (can be disabled?)
Configuration
- /etc/passwd
- /etc/group
- /etc/fstab
Binaries
Feature Sets
Feature sets consist of lists for the set of modules and files that need to be included in a final initramfs to support the indicated feature.
Init
/sbin/init is the first process to be started in the live system after the initramfs completes its work. It is part of the Busybox package and should not be confused with the /init script mentioned above.
Loading of Kernel Modules
/etc/init.d/modules loads all modules specified in /etc/modules and /(etc|run|usr/lib|lib)/modules-load.d/*.conf