Installation: Difference between revisions
Dubiousjim (talk | contribs) (→Basics: USB "key" -> "drive") |
m (→Verifying the downloaded image-file: Replace ridiculous powershell only command with one that is available in any command interpreter on more versions of Windows.) |
||
(652 intermediate revisions by 51 users not shown) | |||
Line 1: | Line 1: | ||
[[Image:hdd_mount.png|left|link=]] | [[Image:hdd_mount.png|left|link=]] | ||
<br /> | <br /> | ||
This page exists to provide a basic overview to get started. Before actually installing, it can help to skim through the [[Alpine_Linux:FAQ| Frequently Asked Questions (FAQ)]], as well as to refer to the official installation guide at [https://docs.alpinelinux.org/ docs.alpinelinux.org]. | |||
[ | |||
{{Tip|This is a wiki! | |||
If something isn't correct, or is incomplete, you will have to figure it out, or ask for the correct solution in the [https://alpinelinux.org/community/ community]. | |||
And then carefully edit the wiki page. | |||
Just as those before who did it for you.}} | |||
== Minimal Hardware Requirements == | |||
{{Main|Requirements}} | |||
* At least 128 MB of RAM. [A graphical desktop system may require up to 512 minimum.]. Note that an installation itself (from ISO) generally requires at least 320 MB during installation. | |||
* At least 0-700 MB space on a writable storage device. [Only required in "sys" or "data" mode installations (explained below). It is optional in "diskless" mode, where it may be used to save newer data and configurations states of a running system.] | |||
== Installation Overview == | |||
== | === The general course of action === | ||
{{Note| | |||
* For single-board-computer (SBC) architectures which can not boot .iso images, see [[Alpine_on_ARM|Alpine on ARM]] for peculiarities. | |||
* For headless system, initial network setup may be fed by pre-built <code>apkovl</code> overlay file, custom-made or via [https://github.com/macmpi/alpine-linux-headless-bootstrap/ 3rd party]}} | |||
As usual, starting an installation procedure requires some basic steps (additional details for all the steps follow [[Installation#Basic Installation Step Details|below]]):<br> | |||
# Downloading and verifying the proper [https://alpinelinux.org/downloads/ stable-release ISO installation image-file] for the target computer's architecture with their corresponding <code>sha256</code> (checksum) and <code>GPG</code> (signature) files. | |||
# Preparing the installation media (e.g.: CD, DVD, USB drive, SD Card, etc). | |||
< | # Optionally, custom-made headless apkovl can be done by first booting the install media on some computer with a display and keyboard attached, or in a virtual machine, and doing an intermediate "diskless" setup of just the boot media (more details below), i.e. using the offical <code>[[Alpine_setup_scripts#setup-alpine|setup-alpine]]</code> to configure the system's network, possibly for dhcp if needed, a ssh server, and a login user. Choosing "disks=none" for now, yet, configure to store configs on the boot media (if it is writable, otherwise on a separate storage media). And afterwards calling <code>[[Alpine_local_backup|lbu commit]]</code> to store the configs as local backup. Then your completed setup, including its securely created own private keys, will readily get (re)loaded on every subsequent (headless) boot from your custom-build <code><hostname>.apkovl.tar.gz</code> stored on the boot media (or on an auxilary media or server location, in case the boot media is read-only). | ||
< | # Booting the target computer from the prepared disk or storage device. | ||
The boot process of the alpine installation image first copies the entire operating system into the RAM memory, and then already starts a complete Alpine Linux system from there. It will initially only provide a basic command line environment that does not depend on reading from any (possibly slow) initial boot media, anymore. | |||
Local log-in is possible as the user <code>root</code>. Initially, the root user has no password. | |||
At the command prompt, an interactive script named <code>setup-alpine</code> is available to configure and install the initial Alpine Linux system. | |||
The question-and-answer dialog of <code>setup-alpine</code> takes care of the base configuration and allows to configure the system to boot into one of three different '''Alpine Linux "disk" modes''': '''"diskless"'''(none), '''"data"''', or '''"sys"'''. | |||
These modes are explained in more detail in the following subsections. | |||
{{Note|It is really helpful for many cases that it is possible to first only complete a basic setup of the initial "diskless" installation media in order to prepare for the installation of the target system. For example, also to download and install some specific driver or software tool. And to possibly use more specific [[Alpine_setup_scripts|setup-scripts]] afterwards in order to proceed with the final installation in a custom way. A most basic pre-setup of just the "diskless" system may be completed by running <code>setup-alpine</code> and answering "none" when asked for the disk to use, for where to store configs, and for the location of the package cache. | |||
< | Examples of preparation options: | ||
* [[ | |||
* [[ | * Preparing a custom partitioning or filesystem scheme that avoids to use and/or overwrite an entire disk ([[Installation#Custom_partitioning_of_the_harddisk|details below]]). | ||
< | * Installing something that may be missing in the live system to configure the hardware, e.g. by using the alpine package manager <code>[[Alpine_Package_Keeper|apk]]</code>. | ||
* [[Alpine | |||
** [[Back Up a Flash Memory Installation]] | Examples of proceeding options: | ||
** [[Manually editing a existing apkovl]] | |||
* [[ | * <code>[[Alpine_setup_scripts#setup-lbu|setup-lbu]]</code> to configure a "local backup" location for the diskless system, and <code>[[Alpine_local_backup|lbu commit]]</code> to then save the local configuration state. | ||
* <code>[[Alpine_setup_scripts#setup-apkcache|setup-apkcache]]</code> to configure a local package cache storage location. | |||
* <code>[[Alpine_setup_scripts#setup-disk|setup-disk]]</code> to add a "data" mode partition, or do a classic full install of the "diskless" system onto a "sys" disk or partition. | |||
There are many more [[Alpine_setup_scripts|setup-scripts]] available. All these tools may also be run later to adjust specific configurations. For example, to set up a graphical environment as covered under [[Installation#Post-Installation|Post-Installation]] below. | |||
}} | |||
==='''Diskless Mode'''=== | |||
This means the entire operating system with all applications are first loaded into RAM and then only run from there. This is the method already used to boot the .iso installation images, however <code>[[Alpine_setup_scripts#setup-alpine|setup-alpine]]</code> can also configure the installed system to continue to boot like this if "disk=none" is specified. The mode is extremely fast and can save on unnecessary disk spin-ups, power, and wear. It is similar to what other linux distributions may call a "frugal" install or boot into with a "toram" option. | |||
Custom configurations and package installations may optionally still be preserved or "persist" across reboots by using the Alpine local backup tool <code>[[Alpine_local_backup|lbu]]</code>. It enables committing and reverting system states by using .apkovl files that are saved to writable storage and loaded when booting. If additional or updated packages have been added to the system, these may also be made available for automatic (re)installation during the boot phase without any (re)downloading, by enabling a [[Alpine_Package_Keeper#Local_Cache|local package cache]] on the writable storage. | |||
[[https://gitlab.alpinelinux.org/alpine/alpine-conf/-/issues/10473 FIXME-1]: Storing local configs and the package cache on '''internal disks still require''' [[Alpine_local_backup#Saving_and_loading_ISO_image_customizations|some manual steps]] to have the partition listed, i.e. making a /etc/fstab entry, mountpoint, and mount, *before* running setup-alpine. The linked workaround also still requires to commit these configurations to disk manually before rebooting.] | |||
If a writable partition is available, <code>setup-alpine</code> can be told to store the configs and the package cache on that writable partition. (Later, another directory on that same partition or another available partition may also be mounted as /home, or for example, for selected important applications to keep their run-time and user data on it.) | |||
The boot device of the newly configured local "diskless" system may remain the initial (and possibly read-only) installation media. But it is also possible to copy the boot system to a partition (e.g. /dev/sdXY) with <code>[[Alpine_setup_scripts#setup-bootable|setup-bootable]]</code>. | |||
==='''Data Disk Mode'''=== | |||
This mode also runs from system RAM, thus it enjoys the same accelerated operation speed as "diskless" mode. However, swap storage and the entire {{Path|/var}} directory tree get mounted from a persistent storage device (two newly created partitions). The directory {{Path|/var}} holds e.g. all log files, mailspools, databases, etc., as well as <code>[[Alpine_local_backup|lbu]]</code> backup commits and the package cache. This mode is useful for having RAM accelerated servers with variable amounts of user-data that exceed the available RAM size. It enables the entire current system state (not just the boot state) to survive a system crash in accordance with the particular filesystem guarantees. | |||
[[https://gitlab.alpinelinux.org/alpine/alpine-conf/-/issues/10474 FIXME-2]]: Setup-alpine will create the data partition and mount it as /var, but '''setup-alpine's "data" disk mode can not yet configure lbu config storage settings automatically'''. The '''current workaround''', is to select "none" at the 'where to store configs' prompt (as the new data partition is not listed anyway) and configure lbu manually after <code>[[Alpine_setup_scripts#setup-alpine|setup-alpine]]</code> exits, and before rebooting: | |||
# Identify the created data partition, e.g. <code>/dev/sd''XY''</code>, and its filesystemtype, e.g. using <code>''lsblk''</code> | |||
# Manually edit the lbu backups location in <code>/etc/lbu/lbu.conf</code> and configure <code>LBU_MEDIA=sd''XY''</code> (according to the previous findings). | |||
# Save the configuration on that partition for the next boot with <code>lbu commit</code>. | |||
# If (a new) partition fails to get mounted, execute: <code>mkdir /media/''sdXY'' ; echo "/dev/sd''XY'' /media/sd''XY'' ''fstype'' noauto,rw 0 0" >> /etc/fstab</code>, and try <code>lbu commit</code> again. | |||
In data disk mode, the boot device may also remain the initial (and possibly read-only) installation media, or be copied to a partition (e.g. /dev/sdXY) with <code>[[Alpine_setup_scripts#setup-bootable|setup-bootable]]</code>. | |||
==='''System Disk Mode'''=== | |||
This is a traditional hard-disk install. | |||
If this mode is selected, the <code>[[Alpine_setup_scripts#setup-alpine|setup-alpine]]</code> script creates three partitions on the selected storage device, {{Path|/boot}}, {{Path|swap}} and {{Path|/}} (the filesystem root). This mode may, for example, be used for generic [[:Category:Desktop|desktop]] and development machines. | |||
For custom partitioning, see [[Setting up disks manually]]. | |||
To install along side another operating systems, see [[Dualbooting]]. | |||
== Preparing for the installation == | |||
{{Note|This "Additional Details" section needs to be consolidated with the work at '''[https://docs.alpinelinux.org https://docs.alpinelinux.org] (not finished)''' | |||
(Restructuring things there, moving and linking from here or there?).}} | |||
=== Verifying the downloaded image-file === | |||
{| class="wikitable" style="width:95%; align=center" | |||
|+ Commands to verify the checksum and GPG signature of a downloaded image-file on different systems. | |||
|- | |||
! width=100px | OS type | |||
! <code>SHA256</code> check !! <code>SHA256</code> calculation (to be compared manually) !! <code>GPG</code> signature verification | |||
|- | |||
! Linux | |||
| <code>sha256sum -c alpine-*.iso.sha256</code> || || <code>curl https://alpinelinux.org/keys/ncopa.asc | gpg --import ;</code> | |||
<code> gpg --verify alpine-<version>.iso.asc alpine-<version>.iso</code> | |||
|- | |||
! MACOS | |||
| - ? - || <code>shasum -a 256 alpine-*.iso</code> || - ? - | |||
|- | |||
! OpenBSD | |||
| <code>sha256 -C alpine-*.sha256 alpine-*.iso</code> || || <code>doas pkg_add gnupg; | |||
ftp -o - https://alpinelinux.org/keys/ncopa.asc | gpg --import ; | |||
gpg --verify alpine-<version>.iso.asc alpine-<version>.iso</code> | |||
|- | |||
! FreeBSD | |||
| - ? - || <code>/usr/local/bin/shasum -a 256 alpine-*.iso</code> || - ? - | |||
|- | |||
! NetBSD | |||
| - ? - || <code>/usr/local/bin/shasum -a 256 alpine-*.iso</code> || - ? - | |||
|- | |||
! Windows | |||
| - ? - || <code>certutil -hashfile alpine-*.iso SHA256</code> || - ? - | |||
|} | |||
=== Flashing (direct data writing) the installation image-file onto a device or media === | |||
{{Seealso|Burning ISOs}} | |||
{{Note|These instructions are exclusively for x86_64 and x86. For ARM boards, see [[Alpine on ARM#Preparing installation media]].}} | |||
==== Unix/Linux ==== | |||
Under Unix (and thus Linux), "everything is a file" and the data in the image-file can be written to a device or media with the <code>dd</code> command. Afterward, executing the <code>eject</code> command removes the target device from the system and ensures the write cache is completely flushed. | |||
{{Cmd|dd if{{=}}<iso-file-to-read-in> of{{=}}<target-device-node-to-write-out-to> bs{{=}}4M; eject <target-device-node-to-write-to>}} | |||
Be careful to correctly identify the target device as any data on it '''will''' be lost! All connected "bulk storage devices" can be listed with <code><nowiki>lsblk</nowiki></code> and <code><nowiki>blkid</nowiki></code>. | |||
# lsblk | |||
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT | |||
sdX 0:0 0 64,0G 0 disk | |||
├─sdX1 0:1 0 2G 0 part | |||
└─sdX2 0:2 0 30G 0 part /mnt/sdX2 | |||
# blkid | |||
/dev/sdX1: LABEL="some" UUID="..." TYPE="vfat" | |||
/dev/sdX2: LABEL="other" UUID="..." TYPE="ext4" | |||
For example, if /dev/sdX is the desired target device, first make sure you un-mount all mounted partitions of the target device. For example sdX1 and sdX2: | |||
{{Cmd|umount /dev/sdX1 /dev/sdX2}} | |||
For <code>dd</code>'s output-file (<code>of=</code>), however, do '''not''' specify a partition number. For example, write to sdX, '''not''' sdX1: | |||
Warning: '''This will overwrite the target device /dev/sdX''', so before executing, make sure you have a backup of the data if you can't afford to lose it. | |||
{{Cmd|dd if{{=}}~/Downloads/alpine-standard-3.00.0-x86_64.iso of{{=}}/dev/sdX bs{{=}}4M; eject /dev/sdX}} | |||
==== Windows ==== | |||
For example, there is the [https://rufus.ie/ Rufus] program. Rufus will enable you to create bootable USB flash drives under Windows. | |||
Rufus has been tested and works for Alpine Linux 3.12.x with the following settings: | |||
* '''Partition scheme''': <code>MBR</code> | |||
* '''Target system''': <code>BIOS or UEFI</code> | |||
* '''File system''': <code>FAT32</code> | |||
* '''Cluster size''': <code>4096 bytes (default)</code> | |||
=== Verifying the written installation media === | |||
After detaching and re-attaching the device, a bit-wise comparison can verify the data written to the device (instead of just data buffered in RAM). If the comparison terminates with an end-of-file error on the .iso file side, all the contents from the image have been written (and re-read) successfully: | |||
# cmp ~/Downloads/alpine-standard-3.00.0-x86_64.iso /dev/sdX | |||
cmp: EOF on alpine-standard-3.00.0-x86_64.iso | |||
=== Booting from external devices === | |||
Insert the boot media to a proper drive or port of the computer and turn the machine on, or restart it, if already running. | |||
If the computer does not automatically boot from the desired device, one needs to bring up the boot menu and choose the media to boot from. Depending on the computer, the menu may be accessed by repeatedly pressing a key quickly when booting starts. Some computers require that you press the button ''before'' starting the computer and hold it down while the computer boots. Typical keys are: {{key|F9}}-{{key|F12}}, sometimes {{key|F7}} or {{key|F8}}. If these don't bring up the boot menu, it may be necessary to enter the BIOS configuration and adjust the boot settings, for which typical keys are: {{key|Del}} {{key|F1}} {{key|F2}} {{key|F6}} or {{key|Esc}}. | |||
== Installation Step Details == | |||
=== Custom partitioning of the harddisk === | |||
It is possible to specify configurations for RAID, encryption, LVM, etc. as well as manual partitioning. | |||
For "diskless" or "data disk" mode installs, manual partitioning may be needed to prepare the harddisk for committing local backups of the system state with <code>[[Alpine_local_backup|lbu commit]]</code>, to have a place for a package cache, or to use it for a /var mount. | |||
For a "sys" install, custom partitioning is needed only if the desired scheme differs from overwriting an entire disk, or using the default set of a /boot, swap and root partition on the disk. | |||
See [[Setting up disks manually]] for the alpine options for RAID, encryption, LVM, etc. and manual partitioning. | |||
=== Questions asked by <code>setup-alpine</code> === | |||
[[File:Installation-alpine-alpine-setup-3-setup-scripts.png|350px|thumb|right|Example <code>[[Alpine_setup_scripts#setup-alpine|setup-alpine]]</code> session]] | |||
The <code>[[Alpine_setup_scripts#setup-alpine|setup-alpine]]</code> script offers the following configuration options: | |||
* '''Keyboard Layout''' (Local keyboard language and usage mode, e.g. ''us'' and variant of ''us-nodeadkeys''.) | |||
* '''Hostname''' (The name for the computer.) | |||
* '''Network''' (For example, automatic IP address discovery with the "DHCP" protocol.) | |||
* '''DNS Servers''' (Domain Name Servers to query. If unsure, leave DNS domain name blank and using <code>[https://quad9.net/ 9.9.9.9 2620:fe::fe]</code> for DNS is typically adequate.) | |||
* '''Root password''' (the password used to login to the root account) | |||
* '''Timezone''' (Optionally display times/dates in your local time zone) | |||
* '''HTTP/FTP Proxy''' (Proxy server to use for accessing the web/ftp. Use "none" for direct connections to websites and FTP servers.) | |||
* '''Mirror''' (From where to download packages. Choose the organization you trust giving your usage patterns to.) | |||
* '''Setup a user''' (Setting up a regular user account) | |||
* '''SSH''' (Secure SHell remote access server. "OpenSSH" is part of the default install image. Use "none" to disable remote login, e.g. on laptops.) | |||
* '''Disk Mode''' (Select between diskless (disk="none"), "data" or "sys", as described above.) | |||
{{Warning|The data on a chosen device will be overwritten!}} | |||
* '''NTP''' (Network Time Protocol client used for keeping the system clock in sync with a time server. Package "chrony" is part of the default install image.) | |||
=== Preparing for the first boot === | |||
If <code>[[Alpine_setup_scripts#setup-alpine|setup-alpine]]</code> has finished configuring the "sys" disk mode, the system should be ready to reboot right away (see next subsection). | |||
If the new local system was configured to run in "diskless" or "data" mode, and you do not want keep booting from the initial (and possibly read-only) installation media, the boot system needs to be copied to another device or partition. | |||
The target partition may be identified using {{ic|lsblk}} (after installing it with {{ic|apk add {{pkg|lsblk}}}}) and/or {{ic|blkid}}, similar to previously identifying the initial installation media device. | |||
The procedure to copy the boot system is explained at [[Alpine_setup_scripts#setup-bootable|setup-bootable]] | |||
Once everything is in place, save your customized configuration with {{ic|lbu commit}} before rebooting. | |||
=== Rebooting and testing the new system === | |||
First, remove the initial installation media from the boot drive, or detach it from the port it's connected to. | |||
The system may now be power-cycled or rebooted to confirm everything is working correctly. | |||
The relevant commands for this are {{ic|poweroff}} or {{ic|reboot}}. | |||
=== Completing the installation === | |||
The installation script installs only the base operating system. '''No''' applications e.g. web server, mail server, desktop environment, or web browsers are installed. | |||
Please look under [[Installation#Post-Installation|Post-Installation]] below, for some common things to do after installation. | |||
= Further Installation Instructions = | |||
{{Note| Specific topics should be kept on separate, individually manageable topic-pages and only get listed with a direct reference (link) on this general page.}} | |||
=== Installation === | |||
* [[Kernels]] ''(kernel selection, e.g. for VMs or RPi)'' | |||
* [[How to make a custom ISO image with mkimage]] ''(installation media with its own configuration)'' | |||
* [[Directly booting an ISO file]] ''(without flashing it to a disk or device)'' | |||
* [[Dualbooting|Dual/multi-boot install to HDD partition]] | |||
* [[Netboot Alpine Linux using iPXE]] | |||
Also see other [[:Category:Installation|Installation Category]] pages. | |||
=== Post-Installation === | |||
<!-- COMMENT FOR EDITORS | |||
If you edit Post-Install, | |||
* Consider that there are already [[Tutorials_and_Howtos#Post-Install]], [[Developer_Documentation#Package_management]] and the Handbook, please work towards reducing duplication and providing an overview, and maintaining topic details of considerable size on their own pages. | |||
* Here, only the most relevant jumping off points are listed, not exact list duplicates!!! | |||
* Keep short-list of links here, as overview to more detailed topic specific pages. | |||
* Don't aggregate different topics at yet another place. | |||
--> | |||
* [[Setting up a new user]] ''(to allow remote, console, or graphical logins)'' | |||
* [[Tutorials_and_Howtos#Networking_2|Setting up Networking]] ''(including non-standard configurations)'' | |||
* [[Alpine_Package_Keeper|Package Management (apk)]] ''(how to search/add/del packages etc.)'' | |||
** [[Alpine_Package_Keeper#Upgrade_a_Running_System|Upgrading Alpine]] ''(checking for and installing updates)'' | |||
** [[Repositories#Managing_repositories|Enable the community repository]] ''(access to additional packages)'' | |||
* [[Alpine_Linux:FAQ#Why_don.27t_I_have_man_pages_or_where_is_the_.27man.27_command.3F|man command/man pages]] | |||
* [[Change default shell]] | |||
* [[Running glibc programs]] ''(installation and development)'' | |||
<br> | |||
* [[Alpine_local_backup|Local backup utility <code>lbu</code>]] ''(persisting RAM system configurations)'' | |||
** [[Back Up a Flash Memory Installation]] ''("diskless mode" systems)'' | |||
** [[Manually editing a existing apkovl]] ''(the stored custom configs)'' | |||
<br> | |||
* [[OpenRC|Init System (OpenRC)]] ''(configure a service to automatically boot at next reboot)'' | |||
** [[Writing Init Scripts]] | |||
** [[Multiple Instances of Services]] | ** [[Multiple Instances of Services]] | ||
<br> | |||
* [[Alpine setup scripts#setup-xorg-base|<code>setup-xorg-base</code>]] ''(setup graphical base environment)'' | |||
** [[Tutorials_and_Howtos#Desktop|Desktop Environments]] | |||
<br> | |||
* [[ | * [[Hosting services on Alpine]] ''(links to several mail/web/ssh server setup pages)'' | ||
< | <br> | ||
* [[How to get regular stuff working]] ''(things one may miss in a too lightweight installation )'' | |||
* Running applications and services in their own [[Firejail Security Sandbox]] | |||
=== Broader Usage Guides === | |||
* See: [[Tutorials and Howtos]] | |||
= General Documentation = | |||
{{Tip| Alpine Linux packages stay close to the upstream design. Therefore, all upstream documentation about configuring a software package, as well as good configuration guides from other distributions that stay close to upstream, e.g. those in the [https://wiki.archlinux.org/ ArchWiki], are to a large degree, also applicable to configuring the software on Alpine Linux, thus can be very useful.}} | |||
* [[Alpine_Linux:FAQ|FAQs]] | |||
* [[FAQ|FAQs]] | * [[Alpine_Linux:Contribute|How to Contribute]] | ||
* [[ | |||
* [[Developer Documentation]] | * [[Developer Documentation]] | ||
* [[Alpine_Linux:Wiki_etiquette|Wiki etiquette]] ''(to collaborate on this documentation)'' | |||
* [[Comparison with other distros]] ''(how common things are done on Alpine)'' | |||
---- | |||
[[Category:Installation]] | [[Category:Installation]] |
Revision as of 11:27, 22 January 2024
This page exists to provide a basic overview to get started. Before actually installing, it can help to skim through the Frequently Asked Questions (FAQ), as well as to refer to the official installation guide at docs.alpinelinux.org.
If something isn't correct, or is incomplete, you will have to figure it out, or ask for the correct solution in the community.
And then carefully edit the wiki page.
Just as those before who did it for you.Minimal Hardware Requirements
- At least 128 MB of RAM. [A graphical desktop system may require up to 512 minimum.]. Note that an installation itself (from ISO) generally requires at least 320 MB during installation.
- At least 0-700 MB space on a writable storage device. [Only required in "sys" or "data" mode installations (explained below). It is optional in "diskless" mode, where it may be used to save newer data and configurations states of a running system.]
Installation Overview
The general course of action
- For single-board-computer (SBC) architectures which can not boot .iso images, see Alpine on ARM for peculiarities.
- For headless system, initial network setup may be fed by pre-built
apkovl
overlay file, custom-made or via 3rd party
As usual, starting an installation procedure requires some basic steps (additional details for all the steps follow below):
- Downloading and verifying the proper stable-release ISO installation image-file for the target computer's architecture with their corresponding
sha256
(checksum) andGPG
(signature) files. - Preparing the installation media (e.g.: CD, DVD, USB drive, SD Card, etc).
- Optionally, custom-made headless apkovl can be done by first booting the install media on some computer with a display and keyboard attached, or in a virtual machine, and doing an intermediate "diskless" setup of just the boot media (more details below), i.e. using the offical
setup-alpine
to configure the system's network, possibly for dhcp if needed, a ssh server, and a login user. Choosing "disks=none" for now, yet, configure to store configs on the boot media (if it is writable, otherwise on a separate storage media). And afterwards callinglbu commit
to store the configs as local backup. Then your completed setup, including its securely created own private keys, will readily get (re)loaded on every subsequent (headless) boot from your custom-build<hostname>.apkovl.tar.gz
stored on the boot media (or on an auxilary media or server location, in case the boot media is read-only). - Booting the target computer from the prepared disk or storage device.
The boot process of the alpine installation image first copies the entire operating system into the RAM memory, and then already starts a complete Alpine Linux system from there. It will initially only provide a basic command line environment that does not depend on reading from any (possibly slow) initial boot media, anymore.
Local log-in is possible as the user root
. Initially, the root user has no password.
At the command prompt, an interactive script named setup-alpine
is available to configure and install the initial Alpine Linux system.
The question-and-answer dialog of setup-alpine
takes care of the base configuration and allows to configure the system to boot into one of three different Alpine Linux "disk" modes: "diskless"(none), "data", or "sys".
These modes are explained in more detail in the following subsections.
setup-alpine
and answering "none" when asked for the disk to use, for where to store configs, and for the location of the package cache.
Examples of preparation options:
- Preparing a custom partitioning or filesystem scheme that avoids to use and/or overwrite an entire disk (details below).
- Installing something that may be missing in the live system to configure the hardware, e.g. by using the alpine package manager
apk
.
Examples of proceeding options:
setup-lbu
to configure a "local backup" location for the diskless system, andlbu commit
to then save the local configuration state.setup-apkcache
to configure a local package cache storage location.setup-disk
to add a "data" mode partition, or do a classic full install of the "diskless" system onto a "sys" disk or partition.
There are many more setup-scripts available. All these tools may also be run later to adjust specific configurations. For example, to set up a graphical environment as covered under Post-Installation below.
Diskless Mode
This means the entire operating system with all applications are first loaded into RAM and then only run from there. This is the method already used to boot the .iso installation images, however setup-alpine
can also configure the installed system to continue to boot like this if "disk=none" is specified. The mode is extremely fast and can save on unnecessary disk spin-ups, power, and wear. It is similar to what other linux distributions may call a "frugal" install or boot into with a "toram" option.
Custom configurations and package installations may optionally still be preserved or "persist" across reboots by using the Alpine local backup tool lbu
. It enables committing and reverting system states by using .apkovl files that are saved to writable storage and loaded when booting. If additional or updated packages have been added to the system, these may also be made available for automatic (re)installation during the boot phase without any (re)downloading, by enabling a local package cache on the writable storage.
[FIXME-1: Storing local configs and the package cache on internal disks still require some manual steps to have the partition listed, i.e. making a /etc/fstab entry, mountpoint, and mount, *before* running setup-alpine. The linked workaround also still requires to commit these configurations to disk manually before rebooting.]
If a writable partition is available, setup-alpine
can be told to store the configs and the package cache on that writable partition. (Later, another directory on that same partition or another available partition may also be mounted as /home, or for example, for selected important applications to keep their run-time and user data on it.)
The boot device of the newly configured local "diskless" system may remain the initial (and possibly read-only) installation media. But it is also possible to copy the boot system to a partition (e.g. /dev/sdXY) with setup-bootable
.
Data Disk Mode
This mode also runs from system RAM, thus it enjoys the same accelerated operation speed as "diskless" mode. However, swap storage and the entire /var directory tree get mounted from a persistent storage device (two newly created partitions). The directory /var holds e.g. all log files, mailspools, databases, etc., as well as lbu
backup commits and the package cache. This mode is useful for having RAM accelerated servers with variable amounts of user-data that exceed the available RAM size. It enables the entire current system state (not just the boot state) to survive a system crash in accordance with the particular filesystem guarantees.
[FIXME-2]: Setup-alpine will create the data partition and mount it as /var, but setup-alpine's "data" disk mode can not yet configure lbu config storage settings automatically. The current workaround, is to select "none" at the 'where to store configs' prompt (as the new data partition is not listed anyway) and configure lbu manually after setup-alpine
exits, and before rebooting:
- Identify the created data partition, e.g.
/dev/sdXY
, and its filesystemtype, e.g. usinglsblk
- Manually edit the lbu backups location in
/etc/lbu/lbu.conf
and configureLBU_MEDIA=sdXY
(according to the previous findings). - Save the configuration on that partition for the next boot with
lbu commit
. - If (a new) partition fails to get mounted, execute:
mkdir /media/sdXY ; echo "/dev/sdXY /media/sdXY fstype noauto,rw 0 0" >> /etc/fstab
, and trylbu commit
again.
In data disk mode, the boot device may also remain the initial (and possibly read-only) installation media, or be copied to a partition (e.g. /dev/sdXY) with setup-bootable
.
System Disk Mode
This is a traditional hard-disk install.
If this mode is selected, the setup-alpine
script creates three partitions on the selected storage device, /boot, swap and / (the filesystem root). This mode may, for example, be used for generic desktop and development machines.
For custom partitioning, see Setting up disks manually.
To install along side another operating systems, see Dualbooting.
Preparing for the installation
Verifying the downloaded image-file
OS type | SHA256 check |
SHA256 calculation (to be compared manually) |
GPG signature verification
|
---|---|---|---|
Linux | sha256sum -c alpine-*.iso.sha256 |
curl https://alpinelinux.org/keys/ncopa.asc | gpg --import ;
| |
MACOS | - ? - | shasum -a 256 alpine-*.iso |
- ? - |
OpenBSD | sha256 -C alpine-*.sha256 alpine-*.iso |
doas pkg_add gnupg;
| |
FreeBSD | - ? - | /usr/local/bin/shasum -a 256 alpine-*.iso |
- ? - |
NetBSD | - ? - | /usr/local/bin/shasum -a 256 alpine-*.iso |
- ? - |
Windows | - ? - | certutil -hashfile alpine-*.iso SHA256 |
- ? - |
Flashing (direct data writing) the installation image-file onto a device or media
Unix/Linux
Under Unix (and thus Linux), "everything is a file" and the data in the image-file can be written to a device or media with the dd
command. Afterward, executing the eject
command removes the target device from the system and ensures the write cache is completely flushed.
dd if=<iso-file-to-read-in> of=<target-device-node-to-write-out-to> bs=4M; eject <target-device-node-to-write-to>
Be careful to correctly identify the target device as any data on it will be lost! All connected "bulk storage devices" can be listed with lsblk
and blkid
.
# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sdX 0:0 0 64,0G 0 disk ├─sdX1 0:1 0 2G 0 part └─sdX2 0:2 0 30G 0 part /mnt/sdX2 # blkid /dev/sdX1: LABEL="some" UUID="..." TYPE="vfat" /dev/sdX2: LABEL="other" UUID="..." TYPE="ext4"
For example, if /dev/sdX is the desired target device, first make sure you un-mount all mounted partitions of the target device. For example sdX1 and sdX2:
umount /dev/sdX1 /dev/sdX2
For dd
's output-file (of=
), however, do not specify a partition number. For example, write to sdX, not sdX1:
Warning: This will overwrite the target device /dev/sdX, so before executing, make sure you have a backup of the data if you can't afford to lose it.
dd if=~/Downloads/alpine-standard-3.00.0-x86_64.iso of=/dev/sdX bs=4M; eject /dev/sdX
Windows
For example, there is the Rufus program. Rufus will enable you to create bootable USB flash drives under Windows.
Rufus has been tested and works for Alpine Linux 3.12.x with the following settings:
- Partition scheme:
MBR
- Target system:
BIOS or UEFI
- File system:
FAT32
- Cluster size:
4096 bytes (default)
Verifying the written installation media
After detaching and re-attaching the device, a bit-wise comparison can verify the data written to the device (instead of just data buffered in RAM). If the comparison terminates with an end-of-file error on the .iso file side, all the contents from the image have been written (and re-read) successfully:
# cmp ~/Downloads/alpine-standard-3.00.0-x86_64.iso /dev/sdX cmp: EOF on alpine-standard-3.00.0-x86_64.iso
Booting from external devices
Insert the boot media to a proper drive or port of the computer and turn the machine on, or restart it, if already running.
If the computer does not automatically boot from the desired device, one needs to bring up the boot menu and choose the media to boot from. Depending on the computer, the menu may be accessed by repeatedly pressing a key quickly when booting starts. Some computers require that you press the button before starting the computer and hold it down while the computer boots. Typical keys are: F9-F12, sometimes F7 or F8. If these don't bring up the boot menu, it may be necessary to enter the BIOS configuration and adjust the boot settings, for which typical keys are: Del F1 F2 F6 or Esc.
Installation Step Details
Custom partitioning of the harddisk
It is possible to specify configurations for RAID, encryption, LVM, etc. as well as manual partitioning.
For "diskless" or "data disk" mode installs, manual partitioning may be needed to prepare the harddisk for committing local backups of the system state with lbu commit
, to have a place for a package cache, or to use it for a /var mount.
For a "sys" install, custom partitioning is needed only if the desired scheme differs from overwriting an entire disk, or using the default set of a /boot, swap and root partition on the disk.
See Setting up disks manually for the alpine options for RAID, encryption, LVM, etc. and manual partitioning.
Questions asked by setup-alpine
The setup-alpine
script offers the following configuration options:
- Keyboard Layout (Local keyboard language and usage mode, e.g. us and variant of us-nodeadkeys.)
- Hostname (The name for the computer.)
- Network (For example, automatic IP address discovery with the "DHCP" protocol.)
- DNS Servers (Domain Name Servers to query. If unsure, leave DNS domain name blank and using
9.9.9.9 2620:fe::fe
for DNS is typically adequate.) - Root password (the password used to login to the root account)
- Timezone (Optionally display times/dates in your local time zone)
- HTTP/FTP Proxy (Proxy server to use for accessing the web/ftp. Use "none" for direct connections to websites and FTP servers.)
- Mirror (From where to download packages. Choose the organization you trust giving your usage patterns to.)
- Setup a user (Setting up a regular user account)
- SSH (Secure SHell remote access server. "OpenSSH" is part of the default install image. Use "none" to disable remote login, e.g. on laptops.)
- Disk Mode (Select between diskless (disk="none"), "data" or "sys", as described above.)
- NTP (Network Time Protocol client used for keeping the system clock in sync with a time server. Package "chrony" is part of the default install image.)
Preparing for the first boot
If setup-alpine
has finished configuring the "sys" disk mode, the system should be ready to reboot right away (see next subsection).
If the new local system was configured to run in "diskless" or "data" mode, and you do not want keep booting from the initial (and possibly read-only) installation media, the boot system needs to be copied to another device or partition.
The target partition may be identified using lsblk
(after installing it with apk add lsblk
) and/or blkid
, similar to previously identifying the initial installation media device.
The procedure to copy the boot system is explained at setup-bootable
Once everything is in place, save your customized configuration with lbu commit
before rebooting.
Rebooting and testing the new system
First, remove the initial installation media from the boot drive, or detach it from the port it's connected to.
The system may now be power-cycled or rebooted to confirm everything is working correctly.
The relevant commands for this are poweroff
or reboot
.
Completing the installation
The installation script installs only the base operating system. No applications e.g. web server, mail server, desktop environment, or web browsers are installed.
Please look under Post-Installation below, for some common things to do after installation.
Further Installation Instructions
Installation
- Kernels (kernel selection, e.g. for VMs or RPi)
- How to make a custom ISO image with mkimage (installation media with its own configuration)
- Directly booting an ISO file (without flashing it to a disk or device)
- Dual/multi-boot install to HDD partition
- Netboot Alpine Linux using iPXE
Also see other Installation Category pages.
Post-Installation
- Setting up a new user (to allow remote, console, or graphical logins)
- Setting up Networking (including non-standard configurations)
- Package Management (apk) (how to search/add/del packages etc.)
- Upgrading Alpine (checking for and installing updates)
- Enable the community repository (access to additional packages)
- man command/man pages
- Change default shell
- Running glibc programs (installation and development)
- Local backup utility
lbu
(persisting RAM system configurations)- Back Up a Flash Memory Installation ("diskless mode" systems)
- Manually editing a existing apkovl (the stored custom configs)
- Init System (OpenRC) (configure a service to automatically boot at next reboot)
setup-xorg-base
(setup graphical base environment)
- Hosting services on Alpine (links to several mail/web/ssh server setup pages)
- How to get regular stuff working (things one may miss in a too lightweight installation )
- Running applications and services in their own Firejail Security Sandbox
Broader Usage Guides
- See: Tutorials and Howtos
General Documentation
- FAQs
- How to Contribute
- Developer Documentation
- Wiki etiquette (to collaborate on this documentation)
- Comparison with other distros (how common things are done on Alpine)