Template:Copying Alpine to Flash: Difference between revisions

From Alpine Linux
(setup-bootable expects a formatted partition. added Note to say so)
Line 25: Line 25:
#** Use defaults for first and last cylinder (just press [Enter] twice).
#** Use defaults for first and last cylinder (just press [Enter] twice).
#* '''t''' Change partition type
#* '''t''' Change partition type
#* '''c''' Type: Win95 FAT32 (LBA)
#* '''c''' Partition type (Win95 FAT32/LBA)
#Verify that the primary partition is bootable
#Verify that the primary partition is bootable
#* '''p''' Print list of partitions
#* '''p''' Print list of partitions

Revision as of 14:07, 20 October 2012

Boot Alpine Linux CD-ROM

  1. Insert the Alpine Linux CD-ROM into a computer.
  2. Boot the computer from the Alpine Linux CD-ROM.
    • This step may require changes to the BIOS settings to select booting from CD.
  3. Login with the username root. No password is needed.

Determine the Device Name of the Flash Medium

Determine the name your computer uses for your flash medium. The following step is one way to do this.

  1. After inserting the flash medium, run the command:
    • dmesg

    • At the end of this command you should see the name of your flash medium, likely starting with "sd". (For example: "sda").
    • The remainder of this document will assume that your flash medium is called /dev/sda
Warning: Be very careful about this. You do not want to mistakenly wipe your hard drive if it's on /dev/sda


Format Flash Medium

Run fdisk (replacing sda with your flash medium name):

fdisk /dev/sda

  1. (Optional) - Create new partition table with one FAT32 partition
    • d Delete all partitions (this may take a few steps)
    • n Create a new partition
    • p A primary partition
    • 1 Partition number 1
      • Use defaults for first and last cylinder (just press [Enter] twice).
    • t Change partition type
    • c Partition type (Win95 FAT32/LBA)
  2. Verify that the primary partition is bootable
    • p Print list of partitions
    • If there is no '*' next to the first partition, follow the next steps:
      • a Make the partition bootable (set boot flag)
      • 1 Partition number 1
  3. w Write your changes to the device

Add Alpine Linux to the Flash Medium

To boot from your flash medium you need to copy the contents of the CDROM to the flash medium and make it bootable. Those two operations can be automated with the setup-bootable tool or can be done manually.

Note: If the following commands fail due to 'No such file or directory', you may have to remove and reinsert the flash medium, or even reboot, to get /dev/sda1 to appear

Automated

Tip: If using Alpine Linux 1.10.4 or newer, you can use this section to complete the install. Otherwise, follow the Manual steps below.
  1. Run the setup-bootable script to add Alpine Linux to the flash medium and make it bootable (replacing sda with your flash medium name):

    setup-bootable /media/cdrom /dev/sda1

Note: The target partition has to be formatted. Use the mkdosfs command from the Manual steps below if needed.
Warning: If you are installing to a USB Stick, the setup-bootable script will not use usbdisk in the syslinux.cfg file. You should modify it to say usbdisk as described below, or you will face possible problems booting and definite problems with the package cache.


Manual

  1. (Optional) - If you created a new partition above, format the flash medium with a FAT32 filesystem (replacing sda with your flash medium name):

    apk add dosfstools
    mkdosfs -F32 /dev/sda1

  2. Install syslinux and MBR (replacing sda with your flash medium name):

    apk add syslinux
    dd if=/usr/share/syslinux/mbr.bin of=/dev/sda
    syslinux /dev/sda1

  3. Copy the files to the flash medium (replacing sda with your flash medium name):

    mkdir -p /media/sda1 mount -t vfat /dev/sda1 /media/sda1 cd /media/cdrom cp -a .alpine-release * /media/sda1/ umount /media/sda1

Troubleshooting

Wrong Device Name

If you cannot boot from the flash medium and you see something like:

Mounting boot media failed.
initramfs emergency recovery shell launched. Type 'exit' to continue boot

then it is likely that the device name in syslinux.cfg is wrong. You should replace the device name in the syslinux.cfg line:

append initrd=/boot/grsec.gz alpine_dev=usbdisk:vfat modules=loop,cramfs,sd-mod,usb-storage quiet

with the proper device name.

  • For boot from USB, the device name should be 'usbdisk' (as shown above)
  • For other options, you can run cat /proc/partitions to see the available disks (i.e. 'sda' or 'sdb')

Non-FAT32 Filesystems

When your flash medium is formatted with a filesystem other than FAT32, you might have to specify the necessary filesystem modules in the boot parameters.

To do so, mount the flash medium and change the syslinux.cfg file line from

append initrd=/boot/grsec.gz alpine_dev=usbdisk:vfat modules=loop,cramfs,sd-mod,usb-storage quiet

to

append initrd=/boot/grsec.gz alpine_dev=usbdisk:vfat modules=loop,cramfs,sd-mod,usb-storage,ext3 quiet

in the case of an ext3 formatted partition. A similar procedure might apply to other filesystems (if they are supported by syslinux and the Alpine Linux kernel).