Setting up unbound DNS server: Difference between revisions

From Alpine Linux
Line 46: Line 46:
remote-control:
remote-control:
         control-enable: no
         control-enable: no
## Stub zones are like forward zones (see below) but must only contain authority server (no recursive servers)
#stub-zone:
#        name: "my.test.com"
# stub-addr: 172.16.1.1
# stub-addr: 172.16.1.2
## Note for forward zones, the destination servers must be able to handle recursion to other DNS server
## Note for forward zones, the destination servers must be able to handle recursion to other DNS server
## Forward all *.example.com queries to the server at 192.168.1.1
## Forward all *.example.com queries to the server at 192.168.1.1

Revision as of 12:27, 13 November 2013

Unbound is a validating, recursive, and caching DNS resolver that supports DNSSEC.

Install

Install the unbound package:

apk add unbound

Configure

The following configuration is an example of a caching name server (in a production server, it's recommended to adjust the access-control parameter to limit access to your network). The forward-zone(s) section will forward all DNS queries to the specified servers. Don't forget to change the 'interface' parameter to one of your local interfaces (or 0.0.0.0 to listen on all local IPv4 interfaces). The following is a minimal example with many options commented out.

  • /etc/unbound/unbound.conf
server:
        verbosity: 1
## Specify the interface address to listen on:
        interface: 10.0.0.1
## To listen on all interfaces use the following line instead
#       interface: 0.0.0.0
        do-ip4: yes
        do-ip6: no
        do-udp: yes
        do-tcp: yes
        do-daemonize: yes
        access-control: 0.0.0.0/0 allow
## Other access control examples
#access-control: 192.168.1.0/24 action
## 'action' should be replaced by any one of:
#deny (drop message)
#refuse (sends  a  DNS  rcode REFUSED error message back)
#allow (recursive ok)
#allow_snoop (recursive and nonrecursive ok).
## Minimum lifetime of cache entries in seconds.  Default is 0.
#cache-min-ttl: 60
## Maximum lifetime of cached entries. Default is 86400 seconds (1  day).
#cache-max-ttl: 172800
## enable to not answer id.server and hostname.bind queries. 
        hide-identity: yes
## enable to not answer version.server and version.bind queries. 
        hide-version: yes
## default is to use syslog, which will log to /var/log/messages.
use-syslog: yes
## to log elsewhere, set 'use-syslog' to 'no' and set the log file location below:
#logfile: /var/log/unbound
python:
remote-control:
        control-enable: no
## Stub zones are like forward zones (see below) but must only contain authority server (no recursive servers)
#stub-zone: 
#        name: "my.test.com"
#		 stub-addr: 172.16.1.1
#		 stub-addr: 172.16.1.2
## Note for forward zones, the destination servers must be able to handle recursion to other DNS server
## Forward all *.example.com queries to the server at 192.168.1.1
#forward-zone:
#        name: "example.com"
#        forward-addr: 192.168.1.1
## Forward all other queries to the Verizon DNS servers
forward-zone:      
        name: "."
## Level3 Verizon
        forward-addr: 4.2.2.1
        forward-addr: 4.2.2.4

Set auto-start, start and test the daemon

Check the configuration for errors:

unbound-checkconf

and if no errors are reported, set to auto-start then start unbound:

rc-update add unbound rc-service unbound start

Test, for example:

dig nl.alpinelinux.org @10.0.0.1

or:

nslookup www.google.cz @10.0.0.1

or use drill:

drill www.bbc.co.uk @10.0.0.1

Further information

unbound.conf man page unbound.conf here or here

unbound optimization guide

excellent unbound tutorial at calomel.org

General information via the Wikipedia pages on DNS, record types, zones, name servers and DNSsec