Raspberry Pi 3 - Configuring it as wireless access point -AP Mode: Difference between revisions
m (+ category: Raspberry) |
|||
| (7 intermediate revisions by 4 users not shown) | |||
| Line 1: | Line 1: | ||
{{TOC right}} | |||
=Install the necessary firmware= | |||
apk add linux-firmware-brcm | |||
apk add raspberrypi-libs | |||
=Install hostapd and dnsmasq= | =Install hostapd and dnsmasq= | ||
apk add hostapd | apk add hostapd | ||
apk add dnsmasq | |||
=Configure /etc/hostapd/hostapd.conf= | |||
= | interface=wlan0 | ||
driver=nl80211 | |||
ssid=Pi3-AP | |||
hw_mode=g | |||
channel=1 | |||
macaddr_acl=0 | |||
auth_algs=1 | |||
wpa=2 | |||
wpa_key_mgmt=WPA-PSK | |||
wpa_passphrase=raspberry | |||
rsn_pairwise=CCMP | |||
wpa_pairwise=CCMP | |||
=Configure your /etc/dnsmasq.conf= | |||
interface=wlan0 | interface=wlan0 | ||
dhcp-range=10.0.0.2,10.0.0.5,255.255.255.0,12h | |||
=Configure Static ips for wlan0 in the file /etc/network/interfaces= | |||
auto wlan0 | |||
iface wlan0 inet static | |||
address 10.0.0.1 | |||
netmask 255.255.255.0 | |||
=Start the services= | |||
service dnsmasq start | |||
service hostapd start | |||
=Enable the Services permanently on every bootup= | |||
rc-update add dnsmasq | |||
rc-update add hostapd | |||
(to del) | |||
rc-update del dnsmasq | |||
rc-update del hostapd | |||
(or) | |||
rc-update add dnsmasq boot | |||
rc-update add hostapd boot | |||
(to del) | |||
rc-update del dnsmasq boot | |||
rc-update del hostapd boot | |||
=Commit all changes to files= | |||
Make sure you run the below command to commit all changes otherwise they will be lost on reboot | |||
lbu ci | |||
=References= | =References= | ||
| Line 70: | Line 77: | ||
Thanks | Thanks | ||
oneinsect@gmail.com | oneinsect@gmail.com | ||
[[Category:Networking]] | |||
[[Category:Embedded Systems]] | |||
[[category: Raspberry]] | |||
Revision as of 10:09, 25 October 2019
Install the necessary firmware
apk add linux-firmware-brcm apk add raspberrypi-libs
Install hostapd and dnsmasq
apk add hostapd apk add dnsmasq
Configure /etc/hostapd/hostapd.conf
interface=wlan0 driver=nl80211 ssid=Pi3-AP hw_mode=g channel=1 macaddr_acl=0 auth_algs=1 wpa=2 wpa_key_mgmt=WPA-PSK wpa_passphrase=raspberry rsn_pairwise=CCMP wpa_pairwise=CCMP
Configure your /etc/dnsmasq.conf
interface=wlan0 dhcp-range=10.0.0.2,10.0.0.5,255.255.255.0,12h
Configure Static ips for wlan0 in the file /etc/network/interfaces
auto wlan0 iface wlan0 inet static address 10.0.0.1 netmask 255.255.255.0
Start the services
service dnsmasq start service hostapd start
Enable the Services permanently on every bootup
rc-update add dnsmasq rc-update add hostapd
(to del)
rc-update del dnsmasq rc-update del hostapd
(or)
rc-update add dnsmasq boot rc-update add hostapd boot
(to del)
rc-update del dnsmasq boot rc-update del hostapd boot
Commit all changes to files
Make sure you run the below command to commit all changes otherwise they will be lost on reboot
lbu ci
References
https://gist.github.com/atlury/fe0ea8b91a981c103df7
https://frillip.com/using-your-raspberry-pi-3-as-a-wifi-access-point-with-hostapd/
Thanks oneinsect@gmail.com