Linux Router with VPN on a Raspberry Pi: Difference between revisions

From Alpine Linux
No edit summary
No edit summary
Line 1: Line 1:
Note this article is a work in progress!
= Rationale =
= Rationale =


Line 8: Line 10:


For wireless a separate access point was purchased [http://wiki.openwrt.org/toh/ubiquiti/unifi Ubiquiti UniFi AP] because it contains a Atheros AR9287 which is supported by [https://wireless.wiki.kernel.org/en/users/drivers/ath9k ath9k] and I was keen to avoid blob drivers.
For wireless a separate access point was purchased [http://wiki.openwrt.org/toh/ubiquiti/unifi Ubiquiti UniFi AP] because it contains a Atheros AR9287 which is supported by [https://wireless.wiki.kernel.org/en/users/drivers/ath9k ath9k] and I was keen to avoid blob drivers.
= Installation =
This guide assumes you're using AlpineLinux from a micro sdcard in ram-disk mode. First format the sdcard as described, stop when you get to the end of the [http://wiki.alpinelinux.org/wiki/Create_a_Bootable_USB#Format_USB_stick installation guide Format USB stick]
Download armhf.rpi.tar.gz archive and extract into FAT32 partition. You will need version 3.2.0 or greater if you have a Raspberry Pi 2.


= Modem in full bridge mode =
= Modem in full bridge mode =

Revision as of 19:15, 5 June 2015

Note this article is a work in progress!

Rationale

This guide demonstrates how to set up a Raspberry Pi as an Open Source Linux router with a VPN tunnel.

I had decided against re-flashing a consumer router with an embedded firmware like OpenWrt, DD-WRT or Tomato because these devices were not intended to run alternate firmware.

Support for devices varies significantly depending on which one you have - sometimes down to the revision of the router. Integrating wireless into the device creates significant driver compatibility issues as certain wireless chipsets have better support than others (eg Broadcom and Marvell).

For wireless a separate access point was purchased Ubiquiti UniFi AP because it contains a Atheros AR9287 which is supported by ath9k and I was keen to avoid blob drivers.

Installation

This guide assumes you're using AlpineLinux from a micro sdcard in ram-disk mode. First format the sdcard as described, stop when you get to the end of the installation guide Format USB stick

Download armhf.rpi.tar.gz archive and extract into FAT32 partition. You will need version 3.2.0 or greater if you have a Raspberry Pi 2.

Modem in full bridge mode

Your modem will need to be configured in "full bridge mode". The method for doing this varies depending on the interface on your device and is out of the scope of this tutorial.

The modem I am using is a Cisco 877 Integrated Services Router. It has no web interface and is controlled over SSH. I have put the configuration file up here because it took me some time to figure out the IOS commands to get the device configured in this way.

When sshing into this device with a recent version of ssh you may need to use this command:

  ssh -o HostKeyAlgorithms=ssh-rsa,ssh-dss -o KexAlgorithms=diffie-hellman-group1-sha1 \
-o Ciphers=aes128-cbc,3des-cbc -o MACs=hmac-md5,hmac-sha1 admin@192.168.0.1

As there is a bug here and here with new versions of OpenSSH and Cisco's old sshd.

Configuration of a Cisco 877 ADSL Modem

!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname <HOSTNAME>
!
boot-start-marker
boot-end-marker
!
logging message-counter syslog
logging buffered 4096 informational
enable secret 5 <SECRET>
!
aaa new-model
!
!
aaa authentication login default local
aaa authentication login local_auth local
aaa authorization exec default local none 
!
!
aaa session-id common
!
!
dot11 syslog
ip source-route
no ip routing
!
!
!
!
no ip cef
ip domain name <DOMAIN NAME>
no ipv6 cef
!
multilink bundle-name authenticated
!
!
!
username admin privilege 15 secret 5 <SECRET>
username USER privilege 15 password 7 <SECRET>
! 
!
!
archive
 log config
  hidekeys
!
!
ip ssh version 2
ip scp server enable
!
bridge irb
!
!
interface ATM0
 no ip address
 no ip route-cache
 no atm ilmi-keepalive
 pvc 8/35 
  encapsulation aal5snap
 !
 bridge-group 1
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Dot11Radio0
 no ip address
 no ip route-cache
 shutdown
 speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
 station-role root
!
interface Vlan1
 no ip address
 no ip route-cache
 bridge-group 1
!
interface BVI1
 ip address 192.168.0.1 255.255.255.252
 no ip route-cache
!
ip default-gateway 192.168.0.2
ip default-network 192.168.0.0
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
!
ip access-list standard SSH_ACCESS
!This is a list of the addresses you want to allow
 permit <IP>
 permit <IP>
!
!
!
!
!
!
control-plane
!
bridge 1 protocol ieee
bridge 1 route ip
banner login 
Authorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!


!
line con 0
 no modem enable
line aux 0
line vty 0 4
 access-class SSH_ACCESS in
 authorization exec local_author
 login authentication login_local
 transport input ssh
!
scheduler max-task-time 5000
end

Besides changing the obvious things such as the hostname, domain name, and permitted IPs, you'll also need to verify the ATM0 settings match your ISP's configuration. Specifically: "pvc 8/35" and "encapsulation aal5snap" works for me but may not for you. You will also need to generate the passwords and replace all the instances of <SECRET>.

Generating the passwords

Secret 5 Password

You can generate the hash for the "secret 5" passwords with this OpenSSL command:

   openssl passwd -salt `openssl rand -base64 3` -1 "<YOUR PASSWORD>"

Put the output in <SECRET>

Secret 7 Password

To encrypt the secret 7 password you can use this perl script thanks to m00nie.

#!/usr/bin/perl 
# Cisco (type 7) password tool from www.m00nie.com :D 
# Will either decrypt a _TYPE 7_ password from a cisco device
# or will encrypt a string so that it can be used in a cisco
# device. 
# 
# I made this code to learn more Perl and just out of interest 
# about the type 7 "encryption". The decryption code is already 
# and from a mailing list. The original header from that is below.
#
# Credits for original code and description hobbit@avian.org,
# SPHiXe, .mudge et al. and for John Bashinski <jbash@CISCO.COM>
# for Cisco IOS password encryption facts.
#
# Use for any malice or illegal purposes strictly prohibited!
#

@xlat = ( 0x64, 0x73, 0x66, 0x64, 0x3b, 0x6b, 0x66, 0x6f, 0x41,
          0x2c, 0x2e, 0x69, 0x79, 0x65, 0x77, 0x72, 0x6b, 0x6c,
          0x64, 0x4a, 0x4b, 0x44, 0x48, 0x53 , 0x55, 0x42 );

$loop = 0;
while ($loop == 0) {
	print "\n\n***************************************************************\n";
	print "*    Cisco (type 7) password tool from www.m00nie.com :D      *\n";
	print "* Use for any malice or illegal purposes strictly prohibited! *\n";
        print "***************************************************************\n\n";
	print "1. Decrypt a password\n";
	print "2. Encrypt plain text\n";
	print "3. Quit\n\n";
	print "Pick either 1, 2 or 3: ";
	chomp ($choice = <STDIN>);
	if ( $choice == 1 ) {
		decrypt()
	} elsif ( $choice == 2) {
		encrypt()
	} elsif ($choice == 3) {
		exit
	} else {
		print "$choice is not a valid option\n";
	}		
}

sub decrypt {
print "Enter the encrypted password: ";
chomp ($epass = <STDIN>);

        	if (!(length($epass) & 1)) {
                	$ep = $epass; 
			$dpass = "";
                	($s, $e) = ($ep =~ /^(..)(.+)/);
                	for ($i = 0; $i < length($e); $i+=2){
                  		$dpass .= sprintf "%c",hex(substr($e,$i,2))^$xlat[$s++];
			}
            	}
		print "\nEncrypted pass was: $epass\n";
		print "Decrypted pass is: $dpass\n";
}

sub encrypt {
	print "Enter the string to encrypt:\n";
	chomp ($ptext = <STDIN>);
	$pt = $ptext;
	$etext = "";
	$n = 2;
	$etext .=  sprintf("%.2o", $n);
	for ($k = 0; $k < length($pt); $k+=1){
		$tmp = ord(substr($pt,$k,1))^$xlat[$n++];
		$etext .= sprintf("%.2X", $tmp);
	} 
	print "\nPlain string was: $ptext\n";
	print "Encrypted string is: $etext\n";
}
# eof

Configuring PPP

Next up we need to configure our router to be able to dial a PPP connection with our modem.

apk add ppp-pppoe

Check that the interface between your router and modem is eth1, or change it. Enter your credentials at the bottom of the file or use /etc/ppp/chap-secrets

/etc/ppp/peers/yourISP

nolog

# Try to get the IP address from the ISP
noipdefault

# Try to get the name server addresses from the ISP
usepeerdns

# Use this connection as the default route.
defaultroute

defaultroute-metric 300

# detatch after ppp0 interface is created
updetach

# Replace previous default route
#replacedefaultroute

# rp-pppoe plug-in makes PPPoE connection so rp-pppoe package is not needed
#  Possibly, you may need to change interface according your configuration
plugin rp-pppoe.so eth1

# Uncomment if you need on-demand connection
#demand

# Disconnect after 300 seconds (5 minutes) of idle time.
#idle 300

# Hide password from log entries
hide-password

# Send echo requests
lcp-echo-interval 20
lcp-echo-failure 3

# Do not authenticate ISP peer
noauth

# Control connection consistency
persist
maxfail 0

# Control MTU size if your ISP does not force it
#mtu 1492

# Set your credentials
#  Alternatively you may use /etc/ppp/pap-secrets or /etc/ppp/chap-secrets files
user username@yourISP.tld
password <SECRET>

Network

/etc/network/interfaces

Configure your network interfaces:

auto lo
    iface lo inet loopback

# internal interface
auto eth0
iface eth0 inet static
	address 192.168.1.1
	netmask 255.255.255.0

# external interface
auto eth1
iface eth1 inet static
	address 192.168.0.2
	netmask 255.255.255.252

# internet connection
auto ppp0
iface ppp0 inet ppp
	pre-up ip link set dev eth1 up
	provider <yourISP> # Make sure this is the same as /etc/ppp/peers/yourISP
	post-down ip link set dev eth1 down

Basic IPtables firewall with routing

This demonstrates how to set up basic routing with a permissive outgoing firewall. Incoming packets are blocked.

#!/bin/sh

iptables -F
iptables -t nat -F

export WAN=ppp0
export INT_IF=eth0
export EXT_IF=eth1
export WAN_TUNNEL=tun0

# Allows internet access on gateway
iptables -A INPUT -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT
iptables -A INPUT -m conntrack --ctstate INVALID -j DROP

# ICMP
iptables -A INPUT -p udp -j REJECT --reject-with icmp-port-unreachable
iptables -A INPUT -p tcp -j REJECT --reject-with tcp-rst
iptables -A INPUT -j REJECT --reject-with icmp-proto-unreachable

# SSH To Modem
iptables -A FORWARD -i ${INT_IF} -o ${EXT_IF} -s 192.168.1.0/24 -d 192.168.0.0/30 -j ACCEPT
iptables -A FORWARD -i ${EXT_IF} -o ${INT_IF} -s 192.168.0.0/30 -d 192.168.1.0/24  -j ACCEPT
iptables -A FORWARD -i ${INT_IF} -o ${EXT_IF} -s 192.168.1.0/24 -d 192.168.0.0/30 -j ACCEPT
iptables -A FORWARD -i ${EXT_IF} -o ${INT_IF} -s 192.168.0.0/30 -d 192.168.1.0/24  -j ACCEPT

# SSH To Router
iptables -A INPUT -i ${INT_IF} -p tcp -s 192.168.1.0/24 --dport ssh -m conntrack --ctstate NEW,ESTABLISHED -j ACCEPT
iptables -A INPUT -i ${INT_IF} -p tcp -s 192.168.2.0/24 --dport ssh -m conntrack --ctstate NEW,ESTABLISHED -j ACCEPT
iptables -A OUTPUT -o ${INT_IF} -p tcp --sport ssh -m conntrack --ctstate ESTABLISHED -j ACCEPT

# Accept DNS from LAN (This router runs a DNS forwarder)
iptables -A INPUT -i ${INT_IF} -p tcp -s 192.168.1.0/24 --dport 53 -j ACCEPT                                        
iptables -A OUTPUT -o ${INT_IF} -p tcp --sport 53 -j ACCEPT
iptables -A INPUT -i ${INT_IF} -p udp -s 192.168.1.0/24 --dport 53 -j ACCEPT
iptables -A OUTPUT -o ${INT_IF} -p udp --sport 53 -j ACCEPT

#Locks down certain services so they only work from the LAN:
iptables -I INPUT 1 -i ${INT_IF} -j ACCEPT
iptables -I INPUT 1 -i lo -j ACCEPT
iptables -A INPUT -p UDP --dport bootps ! -i ${INT_IF} -j REJECT
iptables -A INPUT -p UDP --dport domain ! -i ${INT_IF} -j REJECT

# Drop TCP / UDP packets to privileged ports
iptables -A INPUT -p TCP ! -i ${INT_IF} -d 0/0 --dport 0:1023 -j DROP
iptables -A INPUT -p UDP ! -i ${INT_IF} -d 0/0 --dport 0:1023 -j DROP

iptables -I FORWARD -i ${INT_IF} -d 192.168.1.0/24 -j DROP
iptables -A FORWARD -i ${INT_IF} -s 192.168.1.0/24 -j ACCEPT
iptables -A FORWARD -i ${WAN} -d 192.168.1.0/24 -j ACCEPT
iptables -t nat -A POSTROUTING -s 192.168.1.0/24 -o ${WAN} -j MASQUERADE

# Bittorrent forward (before we had a VPN tunnel)
iptables -t nat -A PREROUTING -p tcp --dport 6881:6889 -i ${WAN} -j DNAT --to 192.168.2.100
iptables -t nat -A PREROUTING -p udp --dport 6881:6889 -i ${WAN} -j DNAT --to 192.168.2.100

iptables -P INPUT DROP
iptables -P OUTPUT ACCEPT
iptables -P FORWARD DROP

echo 1 > /proc/sys/net/ipv4/ip_forward
for f in /proc/sys/net/ipv4/conf/*/rp_filter ; do echo 1 > $f ; done

/etc/init.d/iptables save

/etc/sysctl.conf

net.ipv4.ip_forward = 1
net.ipv4.conf.default.rp_filter = 1
kernel.panic = 120

#### ipv4 networking and equivalent ipv6 parameters ####

## TCP SYN cookie protection (default)
## helps protect against SYN flood attacks
## only kicks in when net.ipv4.tcp_max_syn_backlog is reached
net.ipv4.tcp_syncookies = 1

## protect against tcp time-wait assassination hazards
## drop RST packets for sockets in the time-wait state
## (not widely supported outside of linux, but conforms to RFC)
net.ipv4.tcp_rfc1337 = 1

## sets the kernels reverse path filtering mechanism to value 1(on)
## will do source validation of the packet's recieved from all the interfaces on the machine
## protects from attackers that are using ip spoofing methods to do harm
net.ipv4.conf.all.rp_filter = 1
net.ipv6.conf.all.rp_filter = 1

## tcp timestamps
## + protect against wrapping sequence numbers (at gigabit speeds)
## + round trip time calculation implemented in TCP
## - causes extra overhead and allows uptime detection by scanners like nmap
## enable @ gigabit speeds
net.ipv4.tcp_timestamps = 0
#net.ipv4.tcp_timestamps = 1

## log martian packets
net.ipv4.conf.all.log_martians = 1

## ignore echo broadcast requests to prevent being part of smurf attacks (default)
net.ipv4.icmp_echo_ignore_broadcasts = 1

## ignore bogus icmp errors (default)
net.ipv4.icmp_ignore_bogus_error_responses = 1

## send redirects (not a router, disable it)
net.ipv4.conf.all.send_redirects = 0

## ICMP routing redirects (only secure)
#net.ipv4.conf.all.secure_redirects = 1 (default)
net/ipv4/conf/default/accept_redirects=0
net/ipv4/conf/all/accept_redirects=0
net/ipv6/conf/default/accept_redirects=0
net/ipv6/conf/all/accept_redirects=0

# Disable ipv6
net.ipv6.conf.all.disable_ipv6 = 1
net.ipv6.conf.default.disable_ipv6 = 1
net.ipv6.conf.lo.disable_ipv6 = 1

References