Chrony and GPSD: Difference between revisions

From Alpine Linux
No edit summary
(update links & use https)
 
(5 intermediate revisions by 3 users not shown)
Line 2: Line 2:
Sources such as:
Sources such as:


* http://www.rjsystems.nl/en/2100-ntpd-garmin-gps-18-lvc-gpsd.php
* https://www.rjsystems.nl/en/2100-ntpd-garmin-gps-18-lvc-gpsd.php
* http://lists.ntp.org/pipermail/questions/2005-November/007878.html
* https://lists.ntp.org/pipermail/questions/2005-November/007878.html


Describe how to wire a Garmin gps 18 lvc to a serial port to grab the PPS (pulse-per-second) signal to create a Stratum 1 timesource.  Other sources show using ntpd, and the [http://gpsd.berlios.de/gpsd.html gpsd man page] provides config snippets.
Describe how to wire a Garmin gps 18 lvc to a serial port to grab the PPS (pulse-per-second) signal to create a Stratum 1 timesource.  Other sources show using ntpd, and the [http://gpsd.berlios.de/gpsd.html gpsd man page] provides config snippets.
Line 15: Line 15:
* If the GPS 18 LVC is on /dev/ttyS1, then:
* If the GPS 18 LVC is on /dev/ttyS1, then:
{{Cat|/etc/conf.d/gpsd|<nowiki>
{{Cat|/etc/conf.d/gpsd|<nowiki>
# The GPS device (/dev/ttyUSB0, /dev/ttyS0, ...)
# Copyright 1999-2010 Gentoo Foundation
# Distributed under the terms of the GNU General Public License v2
DEVICE="/dev/ttyS1"
BAUDRATE="4800"


# Config file for gpsd server
# Optional arguments
# Optional arguments
#  Options include:
#  Options include:
Line 30: Line 29:
#  -S integer (default 2947) = set port for daemon
#  -S integer (default 2947) = set port for daemon


ARGS="-n -b"
GPSD_OPTIONS="-n -b"
DEVICES="/dev/ttyS1"
GPSD_SOCKET="/var/run/gpsd.sock"
BAUDRATE="4800"


# Serial setup
# Serial setup
#
#
# For serial interfaces, options such as low_latency are recommended
# For serial interfaces, options such as low_latency are recommended
# Also, http://catb.org/gpsd/upstream-bugs.html#tiocmwait recommends
# Also, https://gpsd.gitlab.io/gpsd/upstream-bugs.html#tiocmwait recommends
#  setting the baudrate with stty
#  setting the baudrate with stty
# Uncomment the following lines if using a serial device:
# Uncomment the following lines if using a serial device:
Line 43: Line 45:
</nowiki>
</nowiki>
}}
}}
* This shows all three methods of getting time from gpsd:
 
 
{{Note|As of v3.11, the init.d and conf.d files have been merged from gentoo.
The purpose is to allow gpsd to start without editing /etc/conf.d/gpsd.
Note that while gpsd will now start without editing the conf.d file, it will do so with no gps devices attached. 
 
Also note that if you are using a serial device it is still recommended to add the stty and setserial commands as noted in the example configuration above.}}
 
 
* This shows all four methods of getting time from gpsd:
{{Cat|/etc/chrony/chrony.conf|<nowiki>
{{Cat|/etc/chrony/chrony.conf|<nowiki>
server 0.pool.ntp.org
server 0.pool.ntp.org
Line 51: Line 62:
initstepslew 30 0.pool.ntp.org 1.pool.ntp.org 2.pool.ntp.org
initstepslew 30 0.pool.ntp.org 1.pool.ntp.org 2.pool.ntp.org


# SHM0 from gpsd is the NEMA data at 4800bps, so is not very accurate
# SHM0 from gpsd is the NMEA data at 4800bps, so is not very accurate
refclock SHM 0  delay 0.5 refid NEMA
refclock SHM 0  delay 0.5 refid NMEA


# SHM1 from gpsd (if present) is from the kernel PPS_LDISC
# SHM1 from gpsd (if present) is from the kernel PPS_LDISC
# module.  It includes PPS and will be accurate to a few ns
# module.  It includes PPS and will be accurate to a few ns
refclock SHM 1 offset 0.0 delay 0.1 refid PPS
refclock SHM 1 offset 0.0 delay 0.1 refid NMEA+


# SOCK protocol also includes PPS data and  
# SOCK protocol also includes PPS data and  
# it also provides time within a few ns
# it also provides time within a few ns
refclock SOCK /var/run/chrony.ttyS1.sock delay 0.0 refid SOCK
refclock SOCK /var/run/chrony.ttyS1.sock delay 0.0 refid SOCK
# PPS is from the /dev/pps0 device.  Note that
# chronyd creates the /var/run/chrony.ttyS1.sock device, but
# gpsd creates the /dev/pps0 device
# openrc rules start gpsd /after/ chronyd, so /dev/pps0
#  is not created until after chronyd is started
#  If you want to use pps0, either edit the openrc rules
#  or add this source after gpsd is started
# refclock PPS /dev/pps0 refid PPS


# If you see something in ns... its good.
# If you see something in ns... its good.
Line 91: Line 113:
  MS Name/IP address        Stratum Poll Reach LastRx Last sample
  MS Name/IP address        Stratum Poll Reach LastRx Last sample
  ===============================================================================
  ===============================================================================
  #x NEMA                         0  4  377    14  +684ms[ +684ms] +/-  252ms
  #x NMEA                         0  4  377    14  +684ms[ +684ms] +/-  252ms
  #+ PPS                          0  4  377    13  +2040ns[+2060ns] +/-  50ms
  #+ PPS                          0  4  377    13  +2040ns[+2060ns] +/-  50ms
  #* SOCK                          0  4  377    7  +225ns[ +245ns] +/- 2217ns
  #* SOCK                          0  4  377    7  +225ns[ +245ns] +/- 2217ns
Line 98: Line 120:
  ^? dead.time.server.org          0  10    0  10y    +0ns[  +0ns] +/-    0ns
  ^? dead.time.server.org          0  10    0  10y    +0ns[  +0ns] +/-    0ns


* NEMA (SHM0)  is "x" - its really unstable
* NMEA (SHM0)  is "x" - its really unstable
* PPS (SHM1) is good, but the delay of 0.1 makes it the not-preferred master
* PPS (SHM1) is good, but the delay of 0.1 makes it the not-preferred master
* SOCK is the preferred master
* SOCK is the preferred master
Line 105: Line 127:
== Notes ==
== Notes ==


* In /etc/chrony/chrony.conf, there are three possible time sources:
* In /etc/chrony/chrony.conf, there are four possible time sources:
** SHM 0  (NEMA serial data)
** SHM 0  (NMEA serial data)
** SHM 1  (NEMA with PPS)
** SHM 1  (NMEA with PPS)
** SOCK  (PPS 'proprietary' gpsd/chrony interface)
** SOCK  (PPS 'proprietary' gpsd/chrony interface)
* You only need 1 of them, although all 3 are shown above
** PPS    (PPS only from the serial interface pulse)
* You only need 1 of them, although 3 are shown above
* In the example above, SHM1 is specified with a delay of 0.1 to prevent it from competing with the SOCK protocol
* In the example above, SHM1 is specified with a delay of 0.1 to prevent it from competing with the SOCK protocol
** If you prefer to use the SHM1  source instead of SOCK, then either:
** If you prefer to use the SHM1  source instead of SOCK, then either:
*** comment out the SOCK protocol line
*** comment out the SOCK protocol line
*** or reverse the delay values.
*** or reverse the delay values.
* Note that the SHM0 source (NEMA only, no PPS) is set to a higher delay - don't use it if you have PPS available.
* Note that the SHM0 source (NMEA only, no PPS) is set to a higher delay - don't use it if you have PPS available.
** An example of where you would want to use SHM0 is a USB based gps receiver - they don't have the PPS line
** An example of where you would want to use SHM0 is a USB based gps receiver - they don't have the PPS line
* Chrony creates the SOCK interface; chrony should be started before gpsd.  If you restart chronyd for some reason, make sure you restart gpsd after.
* Chrony creates the SOCK interface; chrony should be started before gpsd.  If you restart chronyd for some reason, make sure you restart gpsd after.
* The SHM0 interface can be used with USB based gps devices.  In this case, use /dev/ttyUSBX in the /etc/conf.d/gpsd file, and leave the stty and setserial lines commented out.
* The SHM0 interface can be used with USB based gps devices.  In this case, use /dev/ttyUSBX in the /etc/conf.d/gpsd file, and leave the stty and setserial lines commented out.
[[Category:Server]]
[[Category:Networking]]

Latest revision as of 21:32, 25 August 2023

Sources such as:

Describe how to wire a Garmin gps 18 lvc to a serial port to grab the PPS (pulse-per-second) signal to create a Stratum 1 timesource. Other sources show using ntpd, and the gpsd man page provides config snippets.


Alpine Linux gpsd package 3.9-r1 and higher has the necessary pps code to interface with chrony. This page lists all of the files for a complete, working example:


  • /etc/modules needs to list the pps_ldisc module - you'll need to manually load it if not doing a reboot

Contents of /etc/modules

pps_ldisc
  • If the GPS 18 LVC is on /dev/ttyS1, then:

Contents of /etc/conf.d/gpsd

# Copyright 1999-2010 Gentoo Foundation # Distributed under the terms of the GNU General Public License v2 # Config file for gpsd server # Optional arguments # Options include: # -b = bluetooth-safe: open data sources read-only # -n = don't wait for client connects to poll GPS # -N = don't go into background # -F sockfile = specify control socket location # -G = make gpsd listen on INADDR_ANY # -D integer (default 0) = set debug level # -S integer (default 2947) = set port for daemon GPSD_OPTIONS="-n -b" DEVICES="/dev/ttyS1" GPSD_SOCKET="/var/run/gpsd.sock" BAUDRATE="4800" # Serial setup # # For serial interfaces, options such as low_latency are recommended # Also, https://gpsd.gitlab.io/gpsd/upstream-bugs.html#tiocmwait recommends # setting the baudrate with stty # Uncomment the following lines if using a serial device: # /bin/stty -F ${DEVICE} ${BAUDRATE} /bin/setserial ${DEVICE} low_latency


Note: As of v3.11, the init.d and conf.d files have been merged from gentoo.

The purpose is to allow gpsd to start without editing /etc/conf.d/gpsd. Note that while gpsd will now start without editing the conf.d file, it will do so with no gps devices attached.

Also note that if you are using a serial device it is still recommended to add the stty and setserial commands as noted in the example configuration above.


  • This shows all four methods of getting time from gpsd:

Contents of /etc/chrony/chrony.conf

server 0.pool.ntp.org server 1.pool.ntp.org server 2.pool.ntp.org initstepslew 30 0.pool.ntp.org 1.pool.ntp.org 2.pool.ntp.org # SHM0 from gpsd is the NMEA data at 4800bps, so is not very accurate refclock SHM 0 delay 0.5 refid NMEA # SHM1 from gpsd (if present) is from the kernel PPS_LDISC # module. It includes PPS and will be accurate to a few ns refclock SHM 1 offset 0.0 delay 0.1 refid NMEA+ # SOCK protocol also includes PPS data and # it also provides time within a few ns refclock SOCK /var/run/chrony.ttyS1.sock delay 0.0 refid SOCK # PPS is from the /dev/pps0 device. Note that # chronyd creates the /var/run/chrony.ttyS1.sock device, but # gpsd creates the /dev/pps0 device # openrc rules start gpsd /after/ chronyd, so /dev/pps0 # is not created until after chronyd is started # If you want to use pps0, either edit the openrc rules # or add this source after gpsd is started # refclock PPS /dev/pps0 refid PPS # If you see something in ns... its good. # 1 second = # 1000 ms = # 1000000 us = # 1000000000 ns logchange 0.5 local stratum 10 logdir /var/log/chrony keyfile /etc/chrony/chrony.keys commandkey 10 dumpdir /var/log/chrony driftfile /var/log/chrony/chrony.drift allow all

Chronyc

If everything is working correctly, a chronyc 'sources' command should look like this:

chronyc> sources
210 Number of sources = 6
MS Name/IP address         Stratum Poll Reach LastRx Last sample
===============================================================================
#x NMEA                          0   4   377    14   +684ms[ +684ms] +/-  252ms
#+ PPS                           0   4   377    13  +2040ns[+2060ns] +/-   50ms
#* SOCK                          0   4   377     7   +225ns[ +245ns] +/- 2217ns
^? tick.tock.com                 2  10   377   318  -5144us[-5144us] +/-   72ms
^? time.keeper.net               3  10   377   720  -4571us[-4567us] +/-  139ms
^? dead.time.server.org          0  10     0   10y     +0ns[   +0ns] +/-    0ns
  • NMEA (SHM0) is "x" - its really unstable
  • PPS (SHM1) is good, but the delay of 0.1 makes it the not-preferred master
  • SOCK is the preferred master
  • The other NTP servers are only used if the local server goes down.

Notes

  • In /etc/chrony/chrony.conf, there are four possible time sources:
    • SHM 0 (NMEA serial data)
    • SHM 1 (NMEA with PPS)
    • SOCK (PPS 'proprietary' gpsd/chrony interface)
    • PPS (PPS only from the serial interface pulse)
  • You only need 1 of them, although 3 are shown above
  • In the example above, SHM1 is specified with a delay of 0.1 to prevent it from competing with the SOCK protocol
    • If you prefer to use the SHM1 source instead of SOCK, then either:
      • comment out the SOCK protocol line
      • or reverse the delay values.
  • Note that the SHM0 source (NMEA only, no PPS) is set to a higher delay - don't use it if you have PPS available.
    • An example of where you would want to use SHM0 is a USB based gps receiver - they don't have the PPS line
  • Chrony creates the SOCK interface; chrony should be started before gpsd. If you restart chronyd for some reason, make sure you restart gpsd after.
  • The SHM0 interface can be used with USB based gps devices. In this case, use /dev/ttyUSBX in the /etc/conf.d/gpsd file, and leave the stty and setserial lines commented out.