Using HSDPA modem - Revision history

Zcrayfish: /* Requirements */ Used canonical URL.

2023-07-29T06:59:14Z

Requirements: Used canonical URL.

← Older revision		Revision as of 06:59, 29 July 2023
Line 4:		Line 4:
	This doc is tested on Alpine-2.1.3.		This doc is tested on Alpine-2.1.3.

	You will need a [~~http~~://en.wikipedia.org/wiki/~~High-Speed_Downlink_Packet_Access~~ HSDPA] USB-modem.<BR>		You will need a [https://en.wikipedia.org/wiki/High_Speed_Packet_Access#High_Speed_Downlink_Packet_Access_(HSDPA) HSDPA] USB-modem.<BR>
	Use 'dmesg \| less' to figure out which /dev/ttyUSB? it uses ''(you'll need to edit the configuration shown below to reflect the correct port number)''.		Use 'dmesg \| less' to figure out which /dev/ttyUSB? it uses ''(you'll need to edit the configuration shown below to reflect the correct port number)''.

Bt129: /* Configfiles */

2021-07-24T09:57:08Z

Configfiles

← Older revision		Revision as of 09:57, 24 July 2021
Line 16:		Line 16:
	echo "ppp_generic" >> /etc/modules-load.d/ppp.conf}}		echo "ppp_generic" >> /etc/modules-load.d/ppp.conf}}

	== ~~Configfiles~~ ==		== Config files ==

	=== /etc/ppp/peers/E220 ===		=== /etc/ppp/peers/E220 ===
	''(The filename 'E220' can be changed ~~to whatever is appropreate for you~~, but you will need to remember it when running pon/poff command)''		''(The filename 'E220' can be changed, but you will need to remember it when running pon/poff command)''
	<pre>debug		<pre>debug
	/dev/ttyUSB0		/dev/ttyUSB0
Line 36:		Line 36:

	=== /etc/ppp/chat-E220-pin ===		=== /etc/ppp/chat-E220-pin ===
	''(The filename 'chat-E220-pin' can be changed ~~to whatever is appropreate for you~~, but you will need modify above ~~configfile~~ to reflect your ~~decition~~)''		''(The filename 'chat-E220-pin' can be changed, but you will need modify the config file shown above to reflect your decision)''
	<pre>ABORT "BUSY"		<pre>ABORT "BUSY"
	ABORT "ERROR"		ABORT "ERROR"
Line 54:		Line 54:

	=== /etc/ppp/chat-E220-nopin ===		=== /etc/ppp/chat-E220-nopin ===
	''(The filename 'chat-E220-nopin' can be changed ~~to whatever is appropreate for you~~, but you will need modify above ~~configfile~~ to reflect your ~~decition~~)''		''(The filename 'chat-E220-nopin' can be changed, but you will need modify the config file shown above to reflect your decision)''
	<pre>ABORT "BUSY"		<pre>ABORT "BUSY"
	ABORT "ERROR"		ABORT "ERROR"
Line 69:		Line 69:
	CONNECT \c		CONNECT \c
	</pre>		</pre>
	{{Note\|Replace ~~above word~~ '''{PIN}''' with the "PIN" of your card ''(typically a 4 digit code)''}}		{{Note\|Replace '''{PIN}''' with the "PIN" of your card ''(typically a 4 digit code)''}}
	{{Note\|Replace ~~above word~~ '''{APN}''' with the "Access Point Name" of the service you use ''(~~for instance mine is~~ "web.omnitel.it")''. If you don't know the Internet APN, ask your service provider}}		{{Note\|Replace '''{APN}''' with the "Access Point Name" of the service you use ''(e.g. "web.omnitel.it")''. If you don't know the Internet APN, ask your service provider}}

	== Routes ==		== Routes ==

Bt129: /* Load modules */

2021-07-24T09:01:58Z

Load modules

← Older revision		Revision as of 09:01, 24 July 2021
Line 12:		Line 12:

	== Load modules ==		== Load modules ==
	Now let's load the driver ''(using the values you just ~~found out~~)'' and ~~prepare~~ it ~~to get~~ automatically ~~loaded~~ at ~~next reboot~~.		Now let's load the driver ''(using the values you just discovered)'' and configure Alpine to load it automatically at boot-up.
	{{cmd\|modprobe ppp_generic		{{cmd\|modprobe ppp_generic
	echo "ppp_generic" >> /etc/modules-load.d/ppp.conf}}		echo "ppp_generic" >> /etc/modules-load.d/ppp.conf}}

Bt129: /* Install packages */

2021-07-24T08:57:17Z

Install packages

← Older revision		Revision as of 08:57, 24 July 2021
Line 8:		Line 8:

	== Install packages ==		== Install packages ==
	Install required packages		Install the required packages
	{{cmd\|apk add ppp}}		{{cmd\|apk add ppp}}

Bt129: /* Requirements */

2021-07-24T08:57:00Z

Requirements

← Older revision		Revision as of 08:57, 24 July 2021
Line 2:		Line 2:

	== Requirements ==		== Requirements ==
	This doc is tested on ~~alpine~~-2.1.3.		This doc is tested on Alpine-2.1.3.

	You will need a [http://en.wikipedia.org/wiki/High-Speed_Downlink_Packet_Access HSDPA] USB-modem.<BR>		You will need a [http://en.wikipedia.org/wiki/High-Speed_Downlink_Packet_Access HSDPA] USB-modem.<BR>
	Use 'dmesg \| less' to figure out which /dev/ttyUSB? it uses ''(you ~~will~~ need to edit below ~~config~~ to reflect ~~this~~)''.		Use 'dmesg \| less' to figure out which /dev/ttyUSB? it uses ''(you'll need to edit the configuration shown below to reflect the correct port number)''.

	== Install packages ==		== Install packages ==

Leo: /* Load modules */

2020-02-12T09:37:28Z

Load modules

← Older revision		Revision as of 09:37, 12 February 2020
Line 14:		Line 14:
	Now let's load the driver ''(using the values you just found out)'' and prepare it to get automatically loaded at next reboot.		Now let's load the driver ''(using the values you just found out)'' and prepare it to get automatically loaded at next reboot.
	{{cmd\|modprobe ppp_generic		{{cmd\|modprobe ppp_generic
	echo "ppp_generic" >> /etc/modules}}		echo "ppp_generic" >> /etc/modules-load.d/ppp.conf}}

	== Configfiles ==		== Configfiles ==

Ncopa: /* Load modules */ use ppp_generic kernel module

2018-05-01T13:53:21Z

Load modules: use ppp_generic kernel module

← Older revision		Revision as of 13:53, 1 May 2018
Line 13:		Line 13:
	== Load modules ==		== Load modules ==
	Now let's load the driver ''(using the values you just found out)'' and prepare it to get automatically loaded at next reboot.		Now let's load the driver ''(using the values you just found out)'' and prepare it to get automatically loaded at next reboot.
	{{cmd\|modprobe ~~ppp~~		{{cmd\|modprobe ppp_generic
	echo "~~ppp~~" >> /etc/modules}}		echo "ppp_generic" >> /etc/modules}}

	== Configfiles ==		== Configfiles ==

Jbilyk: Add Novatel MC679

2012-09-22T16:56:16Z

Add Novatel MC679

@@ Line 172: / Line 172: @@
 OK AT+CGQMIN=1,2,4,3,6,31
 OK AT+CGATT=1
 OK ATD*99#
 CONNECT \c
 </pre>

Jbilyk: /* Huawei E378 */

2012-01-08T08:39:17Z

Huawei E378

← Older revision		Revision as of 08:39, 8 January 2012
Line 100:		Line 100:

	= Huawei E378 =		= Huawei E378 =
			Tested on Alpine 2.3.3.

	Add usb-modeswitch (currently only in testing repo):		Add usb-modeswitch (currently only in testing repo):
	{{cmd\|apk add usb-modeswitch}}		{{cmd\|apk add usb-modeswitch}}

Jbilyk: add config for a Huawei E378

2012-01-02T12:24:51Z

add config for a Huawei E378

← Older revision		Revision as of 12:24, 2 January 2012
Line 98:		Line 98:
	pppd has a statusinformation function that could come in handy		pppd has a statusinformation function that could come in handy
	{{cmd\|pppstats}}		{{cmd\|pppstats}}

			= Huawei E378 =
			Add usb-modeswitch (currently only in testing repo):
			{{cmd\|apk add usb-modeswitch}}

			/etc/modules:
			<pre>
			usbserial vendor=0x12d1 product=0x1446
			</pre>
			/etc/usb_modeswitch.conf:
			<pre>
			# Configuration for the usb_modeswitch package, a mode switching tool for
			# USB devices providing multiple states or modes
			#
			# This file is evaluated by the wrapper script "usb_modeswitch_dispatcher"
			# in /usr/sbin
			# To enable an option, set it to "1", "yes" or "true" (case doesn't matter)
			# Everything else counts as "disable"

			# Disable automatic mode switching globally (e.g. to access the original
			# install storage)
			DisableSwitching=0

			# Enable logging (results in a extensive report file in /var/log, named
			# "usb_modeswitch_<interface-name>" (and probably others)
			EnableLogging=1

			DefaultVendor=0x12d1
			DefaultProduct=0x1446

			TargetVendor=0x12d1
			TargetProduct=0x14ac

			MessageContent="55534243000000000000000000000011060000000000000000000000000000"

			CheckSuccess=5
			</pre>
			/etc/network/interfaces
			<pre>
			auto ppp0
			iface ppp0 inet ppp
			provider E378
			pre-up usb_modeswitch -c /etc/usb_modeswitch.conf
			</pre>
			/etc/ppp/peers/E378:
			<pre>
			debug
			/dev/ttyUSB0
			460800
			crtscts
			modem
			noauth
			usepeerdns
			defaultroute
			noipdefault
			noccp
			nobsdcomp
			novj
			connect '/usr/sbin/chat -v -f /etc/ppp/peers/chat-E378-nopin'
			</pre>
			/etc/ppp/peers/chat-E378-nopin:
			<pre>
			ABORT "BUSY"
			ABORT "ERROR"
			ABORT "NO CARRIER"
			REPORT "CONNECT"
			TIMEOUT "10"
			"" "ATZ"
			OK AT+CGDCONT=1,"ip","isp.telus.com"
			OK AT+CGQREQ=1,2,4,3,6,31
			OK AT+CGQMIN=1,2,4,3,6,31
			OK AT+CGATT=1
			OK ATD*99#
			CONNECT \c
			</pre>