How to configure static routes - Revision history

Sertonix: replace /etc/init.d with rc-service

2023-11-17T10:19:31Z

replace /etc/init.d with rc-service

← Older revision		Revision as of 10:19, 17 November 2023
Line 44:		Line 44:
	To add your defined static routes manually (for testing):		To add your defined static routes manually (for testing):

	{{Cmd\|~~/etc/init.d/~~staticroute start}}		{{Cmd\|rc-service staticroute start}}

	To remove your defined static routes:		To remove your defined static routes:

	{{Cmd\|~~/etc/init.d/~~staticroute stop}}		{{Cmd\|rc-service staticroute stop}}

	There is a 'restart' option to do an automatic stop/start, but it seems less reliable than using the two above.		There is a 'restart' option to do an automatic stop/start, but it seems less reliable than using the two above.

	[[Category:Networking]]		[[Category:Networking]]

Zcrayfish: Marked page as obsolete.

2023-09-06T05:55:38Z

Marked page as obsolete.

← Older revision		Revision as of 05:55, 6 September 2023
Line 1:		Line 1:
			{{Obsolete\|These directions need to be updated for Alpine v3.10+}}

	This document describes how to configure persistent static routes in Alpine Linux so the route definitions survive server reboots.		This document describes how to configure persistent static routes in Alpine Linux so the route definitions survive server reboots.

Zcrayfish: Marked a dead link.

2021-12-20T02:10:27Z

Marked a dead link.

← Older revision		Revision as of 02:10, 20 December 2021
Line 36:		Line 36:
	up ip route add 192.168.100.0/23 via 192.168.0.3		up ip route add 192.168.100.0/23 via 192.168.0.3

	Once editing is complete, remember to save your changes if you are running the OS in RAM (eg: booting from a USB stick) - if you are not sure how to do this, see this article: [http://5718wiki.gatorfone.com/wikka.php?wakka=KennyAralAlpine How to Boot Alpine Linux and Save Settings on a USB Stick] or [[Alpine_local_backup]]		Once editing is complete, remember to save your changes if you are running the OS in RAM (eg: booting from a USB stick) - if you are not sure how to do this, see this article: [http://5718wiki.gatorfone.com/wikka.php?wakka=KennyAralAlpine How to Boot Alpine Linux and Save Settings on a USB Stick]{{dead link}} or [[Alpine_local_backup]]

	You can verify your settings by restarting the server, or by issuing the following commands:		You can verify your settings by restarting the server, or by issuing the following commands:

Bt129: /* Option 2: Create /etc/route.conf */

2021-07-23T17:08:18Z

Option 2: Create /etc/route.conf

← Older revision		Revision as of 17:08, 23 July 2021
Line 19:		Line 19:
	==Option 2: Create /etc/route.conf==		==Option 2: Create /etc/route.conf==

	Use nano, vi, or your favourite ~~installed~~ editor to create the file /etc/route.conf		Use nano, vi, or your favourite editor to create the file /etc/route.conf
	Add each static route on a separate line - for example:		Add each static route on a separate line - for example:

Bt129 at 07:05, 23 July 2021

2021-07-23T07:05:05Z

Dubiousjim: delete Category:HOWTO

2012-03-21T15:58:51Z

delete Category:HOWTO

← Older revision		Revision as of 15:58, 21 March 2012
Line 49:		Line 49:
	There is a 'restart' option to do an automatic stop/start, but it seems less reliable than using the two above.		There is a 'restart' option to do an automatic stop/start, but it seems less reliable than using the two above.

	~~[[Category:HOWTO]]~~ [[Category:Networking]]		[[Category:Networking]]

Dubiousjim: Category:Networking

2012-03-12T08:19:36Z

Category:Networking

← Older revision		Revision as of 08:19, 12 March 2012
Line 49:		Line 49:
	There is a 'restart' option to do an automatic stop/start, but it seems less reliable than using the two above.		There is a 'restart' option to do an automatic stop/start, but it seems less reliable than using the two above.

	[[Category:HOWTO]]		[[Category:HOWTO]] [[Category:Networking]]

Dubiousjim: How to Configure static routes moved to How to configure static routes: Consistency

2012-03-12T07:26:45Z

How to Configure static routes moved to How to configure static routes: Consistency

← Older revision	Revision as of 07:26, 12 March 2012
(No difference)

Dubiousjim: Howto Configure static routes moved to How to Configure static routes: Consistency

2012-03-12T07:25:27Z

Howto Configure static routes moved to How to Configure static routes: Consistency

← Older revision	Revision as of 07:25, 12 March 2012
(No difference)

Dubiousjim: Category:HOWTO

2012-03-12T07:25:07Z

Category:HOWTO

← Older revision		Revision as of 07:25, 12 March 2012
Line 48:		Line 48:

	There is a 'restart' option to do an automatic stop/start, but it seems less reliable than using the two above.		There is a 'restart' option to do an automatic stop/start, but it seems less reliable than using the two above.

			[[Category:HOWTO]]

← Older revision		Revision as of 07:05, 23 July 2021
Line 1:		Line 1:
	This document describes how to configure persistent static routes in Alpine Linux so ~~that~~ the route definitions survive server reboots.		This document describes how to configure persistent static routes in Alpine Linux so the route definitions survive server reboots.

	This process was tested with release 2.1.4, dated 2011-01-07.		This process was tested with release 2.1.4, dated 2011-01-07.
Line 15:		Line 15:
	staticroute="net 10.200.200.0 netmask 255.255.255.0 gw 192.168.202.12"		staticroute="net 10.200.200.0 netmask 255.255.255.0 gw 192.168.202.12"

	If you need to add multiple static routes, just add additional routes to the end of the text between the quotes, with each route separated by a semicolon or a line break (press ENTER).		If you need to add multiple static routes, just add additional routes to the end of the text between the quotes with each route separated by a semicolon or a line break (press ENTER).

	==Option 2: Create /etc/route.conf==		==Option 2: Create /etc/route.conf==

	Use nano, vi, or your favourite installed editor to create the file /etc/route.conf ~~and add~~ each static route on a separate line - for example:		Use nano, vi, or your favourite installed editor to create the file /etc/route.conf
			Add each static route on a separate line - for example:

	net 10.200.200.0 netmask 255.255.255.0 gw 192.168.200.12		net 10.200.200.0 netmask 255.255.255.0 gw 192.168.200.12
	net 10.200.201.0 netmask 255.255.255.0 gw 192.168.200.13		net 10.200.201.0 netmask 255.255.255.0 gw 192.168.200.13

	==Option 3: ~~Setup~~ routes in /etc/network/interfaces==		==Option 3: Set up routes in /etc/network/interfaces==

	If you have static network configuration in /etc/network/interfaces, you can add a static route that gets activated when an interface ~~gets~~ brought up:		If you have static network configuration in /etc/network/interfaces, you can add a static route that gets activated when an interface is brought up:

	auto eth0		auto eth0