Alpine Linux - User contributions [en]

Classic install or sys mode on Raspberry Pi

2019-05-04T21:59:22Z

Mkbucc: cmdline.txt arguments all go the same line. (Remove the "otherwise use echo" stuff I added.)

A howto for classic installation, or "sys mode".

This method works with a desktop PC under Ubuntu and other Linuxes.

= Preparation =

Download the archive from the '''Rasperry Pi armhf''' link [https://alpinelinux.org/downloads/ here].
'''Sha256''' and '''GPG''' links appear next to the link to check the download.

On a class 10 sd-card with a size of 8Go or more, create two partitions:-
* First in '''fat16''' with size of 256Mo. You may have to check <code>boot</code> and <code>lba</code> flags
* Second in '''ext4''' with the remaining place

Eject and insert your SD card in order to recognize all the partitions.

Now go into the first partition ('''fat16''').

Untar the archive with {{pkg|tar}}:
tar zxvf ~/Download/alpine-rpi-*-armhf.tar.gz

Due to a bug, it is recommended to add a file named <code>usercfg.txt</code> into the partition. The file should contain the following single line:

enable_uart=1

Eject the SD card properly, insert it into the Raspberry Pi, plug a usb keyboard in plus the HDMI and network cables, and power on.

When a prompt displays, connect as root without a password.

Summary: Add OSX diskutil instructions for creating FAT16 partition on microSD

== OSX Preparation: creating a FAT16 partition on microSD ==

To create a FAT16 partition with OSX, use the diskutil program and a USB microSD card reader (I used an older version of this: https://www.bestbuy.com/site/insignia-usb-3-0-memory-card-reader/5787406.p?skuId=5787406).

Put the microSD card in reader, the reader in a USB port, and type <code>ls -1 /Volumes</code> in a terminal. Note the name of the microSD volume; for example, VOL1 in the output below:
$ ls -1 /Volumes
Macintosh HD
Preboot
VOL1
$

Unmount the reader, unplug it and re-run <code>ls -1 /Volumes</code>. Verify the microSD volume name is no longer listed and then re-insert the USB reader.

Find the mount point of your microSD volume; for example, disk3 in the output below:
$ diskutil list VOL1
/dev/disk3 (external, physical):
#: TYPE NAME SIZE IDENTIFIER
0: FDisk_partition_scheme *31.4 GB disk3
1: DOS_FAT_16 VOL1 256.0 MB disk3s1
2: Linux 30.0 GB disk3s2
3: Linux_Swap 1.2 GB disk3s3
$

(For help on diskutil command, type <code>diskutil</code> to list all command verbs. For help on a specific verb, add the verb; for example, <code>diskutil partitionDisk</code>)

Destroy all the existing partitions on the microSD card and create two new ones:
# a 256MB, FAT16, DOS-compatible partition and
# a free space gap for the rest of the card

$ diskutil partitionDisk disk3 MBR "MS-DOS FAT16" VOL1 256MB "Free Space" VOL2 R
Started partitioning on disk3
Unmounting disk
Creating the partition map
Waiting for partitions to activate
Formatting disk3s1 as MS-DOS (FAT16) with name VOL1
512 bytes per physical sector
/dev/rdisk3s1: 499472 sectors in 62434 FAT16 clusters (4096 bytes/cluster)
bps=512 spc=8 res=1 nft=2 rde=512 mid=0xf8 spf=244 spt=32 hds=32 hid=2 drv=0x80 bsec=500000
Mounting disk
Finished partitioning on disk3
/dev/disk3 (external, physical):
#: TYPE NAME SIZE IDENTIFIER
0: FDisk_partition_scheme *31.4 GB disk3
1: DOS_FAT_16 VOL1 256.0 MB disk3s1
$

Change your current working directory to the new FAT16 partition and then pickup with the untar instruction in the parent prep section.

$ cd /Volumes/VOL1/

= Installation =

Execute the following commands. Make sure there is an internet connection available otherwise setting up the apk mirrors will fail.

setup-alpine

Set the mapping keyboard, the timezone, how to connect to the network ('''dhcp''' is the best method), say '''none''' at <code>save config</code> and <code>save cache</code>.

apk update

Raspberry Pi has no battery for his hardware clock, so synchronize with an ntp server:

apk add chrony
service chronyd restart
apk add e2fsprogs
mount /dev/mmcblk0p2 /mnt # The second partition, in ext4 format, where Alpine Linux is installing in sys mode
setup-disk -m sys /mnt
mount -o remount,rw /media/mmcblk0p1 # An update in the first partition is required for the next reboot.

Clean up the boot folder in the first partition to drop unused files:

rm -f /media/mmcblk0p1/boot/*
cd /mnt # We are in the second partition
rm boot/boot # Drop the unused symbolink link

Move the image and <code>init ram</code> for Alpine Linux into the right place:

mv boot/* /media/mmcblk0p1/boot/
rm -Rf boot
mkdir media/mmcblk0p1 # It's the mount point for the first partition on the next reboot

Don't worry about the error with the following:

ln -s media/mmcblk0p1/boot boot

Update <code>/etc/fstab</code>:

echo "/dev/mmcblk0p1 /media/mmcblk0p1 vfat defaults 0 0" >> etc/fstab
sed -i '/cdrom/d' etc/fstab # Of course, you don't have any cdrom or floppy on the Raspberry Pi
sed -i '/floppy/d' etc/fstab
cd /media/mmcblk0p1

If you want to active edge repository
sed -i '/edge/s/^#//' etc/apk/repositories # But enable the repository for community if you want vim, mc, php, apache, nginx, etc.

For the next boot, indicate that the root filesystem is on the second partition. If the cmdline.txt file
contains a line that starts with <code>/root</code>, then use sed:

sed -i 's/^/root=\/dev\/mmcblk0p2 /' /media/mmcblk0p1/cmdline.txt
reboot

That works on '''Raspberry Pi 3B''' and '''1B''', but if you have the '''1B''' version, let's be very, very patient (several tens of minutes).

If a hard disk is connected via '''usb''', you can replace the <code>/dev/mmcblk0p2</code> above with <code>/dev/sda1</code>, for example.

If you don't like the '''sed''' above and its expressions, you can use a nano editor instead after executing the following command:

apk add nano

= Post-installation =

The '''Raspberry Pi (RPI)''' has no battery to keep the time updated. Therefore, we need to enable the right service to synchronize with an ntp server:

rc-update del hwclock boot
rc-update add swclock boot
service hwclock stop
service swclock start

Update and upgrade the system:

apk update
apk upgrade

If you want a cool editor ({{Pkg|vim}}), a file manager ({{Pkg|mc}}), and to determine which tasks are running and which services are starting on boot ({{Pkg|htop}}), add the right packages:

apk add vim mc htop
htop
rc-update

The '''RPI 3B''' has wifi on board for networking, so start the service for the encrypted key on wpa2 protocol:

apk add wpa_supplicant
rc-update add wpa_supplicant boot
service wpa_supplicant start
setup-interfaces
Replace the IP address by dhcp for all the interfaces if necessary; select the SSID network for wifi; and add password.
ip addr # to know the IP address for all interfaces

If you want to connect on your remote RPI via <code>ssh</code>, an additional user (''foo'') and the {{Pkg|sudo}} package are required because it's forbidden to connect as root:

apk add sudo
adduser foo
adduser foo wheel
visudo

Uncomment line #82 with <code>wheel ALL=(ALL) ALL</code>. If {{Pkg|vim}} is installed, save the changes by typing '''Esc :x'''

= See also =

* [[Raspberry Pi]]
* [[Raspberry Pi 3 - Setting Up Bluetooth]]
* [[Raspberry Pi 3 - Configuring it as wireless access point -AP Mode]]
* [[Linux Router with VPN on a Raspberry Pi]]

[[Category:Installation]]

Classic install or sys mode on Raspberry Pi

2019-05-03T00:53:48Z

Mkbucc: Fix my previous edit: remove leading slash on root option in cmdline.txt

A howto for classic installation, or "sys mode".

This method works with a desktop PC under Ubuntu and other Linuxes.

= Preparation =

Download the archive from the '''Rasperry Pi armhf''' link [https://alpinelinux.org/downloads/ here].
'''Sha256''' and '''GPG''' links appear next to the link to check the download.

On a class 10 sd-card with a size of 8Go or more, create two partitions:-
* First in '''fat16''' with size of 256Mo. You may have to check <code>boot</code> and <code>lba</code> flags
* Second in '''ext4''' with the remaining place

Eject and insert your SD card in order to recognize all the partitions.

Now go into the first partition ('''fat16''').

Untar the archive with {{pkg|tar}}:
tar zxvf ~/Download/alpine-rpi-*-armhf.tar.gz

Due to a bug, it is recommended to add a file named <code>usercfg.txt</code> into the partition. The file should contain the following single line:

enable_uart=1

Eject the SD card properly, insert it into the Raspberry Pi, plug a usb keyboard in plus the HDMI and network cables, and power on.

When a prompt displays, connect as root without a password.

Summary: Add OSX diskutil instructions for creating FAT16 partition on microSD

== OSX Preparation: creating a FAT16 partition on microSD ==

To create a FAT16 partition with OSX, use the diskutil program and a USB microSD card reader (I used an older version of this: https://www.bestbuy.com/site/insignia-usb-3-0-memory-card-reader/5787406.p?skuId=5787406).

Put the microSD card in reader, the reader in a USB port, and type <code>ls -1 /Volumes</code> in a terminal. Note the name of the microSD volume; for example, VOL1 in the output below:
$ ls -1 /Volumes
Macintosh HD
Preboot
VOL1
$

Unmount the reader, unplug it and re-run <code>ls -1 /Volumes</code>. Verify the microSD volume name is no longer listed and then re-insert the USB reader.

Find the mount point of your microSD volume; for example, disk3 in the output below:
$ diskutil list VOL1
/dev/disk3 (external, physical):
#: TYPE NAME SIZE IDENTIFIER
0: FDisk_partition_scheme *31.4 GB disk3
1: DOS_FAT_16 VOL1 256.0 MB disk3s1
2: Linux 30.0 GB disk3s2
3: Linux_Swap 1.2 GB disk3s3
$

(For help on diskutil command, type <code>diskutil</code> to list all command verbs. For help on a specific verb, add the verb; for example, <code>diskutil partitionDisk</code>)

Destroy all the existing partitions on the microSD card and create two new ones:
# a 256MB, FAT16, DOS-compatible partition and
# a free space gap for the rest of the card

$ diskutil partitionDisk disk3 MBR "MS-DOS FAT16" VOL1 256MB "Free Space" VOL2 R
Started partitioning on disk3
Unmounting disk
Creating the partition map
Waiting for partitions to activate
Formatting disk3s1 as MS-DOS (FAT16) with name VOL1
512 bytes per physical sector
/dev/rdisk3s1: 499472 sectors in 62434 FAT16 clusters (4096 bytes/cluster)
bps=512 spc=8 res=1 nft=2 rde=512 mid=0xf8 spf=244 spt=32 hds=32 hid=2 drv=0x80 bsec=500000
Mounting disk
Finished partitioning on disk3
/dev/disk3 (external, physical):
#: TYPE NAME SIZE IDENTIFIER
0: FDisk_partition_scheme *31.4 GB disk3
1: DOS_FAT_16 VOL1 256.0 MB disk3s1
$

Change your current working directory to the new FAT16 partition and then pickup with the untar instruction in the parent prep section.

$ cd /Volumes/VOL1/

= Installation =

Execute the following commands. Make sure there is an internet connection available otherwise setting up the apk mirrors will fail.

setup-alpine

Set the mapping keyboard, the timezone, how to connect to the network ('''dhcp''' is the best method), say '''none''' at <code>save config</code> and <code>save cache</code>.

apk update

Raspberry Pi has no battery for his hardware clock, so synchronize with an ntp server:

apk add chrony
service chronyd restart
apk add e2fsprogs
mount /dev/mmcblk0p2 /mnt # The second partition, in ext4 format, where Alpine Linux is installing in sys mode
setup-disk -m sys /mnt
mount -o remount,rw /media/mmcblk0p1 # An update in the first partition is required for the next reboot.

Clean up the boot folder in the first partition to drop unused files:

rm -f /media/mmcblk0p1/boot/*
cd /mnt # We are in the second partition
rm boot/boot # Drop the unused symbolink link

Move the image and <code>init ram</code> for Alpine Linux into the right place:

mv boot/* /media/mmcblk0p1/boot/
rm -Rf boot
mkdir media/mmcblk0p1 # It's the mount point for the first partition on the next reboot

Don't worry about the error with the following:

ln -s media/mmcblk0p1/boot boot

Update <code>/etc/fstab</code>:

echo "/dev/mmcblk0p1 /media/mmcblk0p1 vfat defaults 0 0" >> etc/fstab
sed -i '/cdrom/d' etc/fstab # Of course, you don't have any cdrom or floppy on the Raspberry Pi
sed -i '/floppy/d' etc/fstab
cd /media/mmcblk0p1

If you want to active edge repository
sed -i '/edge/s/^#//' etc/apk/repositories # But enable the repository for community if you want vim, mc, php, apache, nginx, etc.

For the next boot, indicate that the root filesystem is on the second partition. If the cmdline.txt file
contains a line that starts with <code>/root</code>, then use sed:

sed -i 's/^/root=\/dev\/mmcblk0p2 /' /media/mmcblk0p1/cmdline.txt
reboot

otherwise, use echo:

echo "root=/dev/mmcblk0p2" >> cmdline.txt

That works on '''Raspberry Pi 3B''' and '''1B''', but if you have the '''1B''' version, let's be very, very patient (several tens of minutes).

If a hard disk is connected via '''usb''', you can replace the <code>/dev/mmcblk0p2</code> above with <code>/dev/sda1</code>, for example.

If you don't like the '''sed''' above and its expressions, you can use a nano editor instead after executing the following command:

apk add nano

= Post-installation =

The '''Raspberry Pi (RPI)''' has no battery to keep the time updated. Therefore, we need to enable the right service to synchronize with an ntp server:

rc-update del hwclock boot
rc-update add swclock boot
service hwclock stop
service swclock start

Update and upgrade the system:

apk update
apk upgrade

If you want a cool editor ({{Pkg|vim}}), a file manager ({{Pkg|mc}}), and to determine which tasks are running and which services are starting on boot ({{Pkg|htop}}), add the right packages:

apk add vim mc htop
htop
rc-update

The '''RPI 3B''' has wifi on board for networking, so start the service for the encrypted key on wpa2 protocol:

apk add wpa_supplicant
rc-update add wpa_supplicant boot
service wpa_supplicant start
setup-interfaces
Replace the IP address by dhcp for all the interfaces if necessary; select the SSID network for wifi; and add password.
ip addr # to know the IP address for all interfaces

If you want to connect on your remote RPI via <code>ssh</code>, an additional user (''foo'') and the {{Pkg|sudo}} package are required because it's forbidden to connect as root:

apk add sudo
adduser foo
adduser foo wheel
visudo

Uncomment line #82 with <code>wheel ALL=(ALL) ALL</code>. If {{Pkg|vim}} is installed, save the changes by typing '''Esc :x'''

= See also =

* [[Raspberry Pi]]
* [[Raspberry Pi 3 - Setting Up Bluetooth]]
* [[Raspberry Pi 3 - Configuring it as wireless access point -AP Mode]]
* [[Linux Router with VPN on a Raspberry Pi]]

[[Category:Installation]]

Classic install or sys mode on Raspberry Pi

2019-04-28T23:02:28Z

Mkbucc: If cmdline.txt contains "^root=", then use sed; otherwise, use echo.

A howto for classic installation, or "sys mode".

This method works with a desktop PC under Ubuntu and other Linuxes.

= Preparation =

Download the archive from the '''Rasperry Pi armhf''' link [https://alpinelinux.org/downloads/ here].
'''Sha256''' and '''GPG''' links appear next to the link to check the download.

On a class 10 sd-card with a size of 8Go or more, create two partitions:-
* First in '''fat16''' with size of 256Mo. You may have to check <code>boot</code> and <code>lba</code> flags
* Second in '''ext4''' with the remaining place

Eject and insert your SD card in order to recognize all the partitions.

Now go into the first partition ('''fat16''').

Untar the archive with {{pkg|tar}}:
tar zxvf ~/Download/alpine-rpi-*-armhf.tar.gz

Due to a bug, it is recommended to add a file named <code>usercfg.txt</code> into the partition. The file should contain the following single line:

enable_uart=1

Eject the SD card properly, insert it into the Raspberry Pi, plug a usb keyboard in plus the HDMI and network cables, and power on.

When a prompt displays, connect as root without a password.

Summary: Add OSX diskutil instructions for creating FAT16 partition on microSD

== OSX Preparation: creating a FAT16 partition on microSD ==

To create a FAT16 partition with OSX, use the diskutil program and a USB microSD card reader (I used an older version of this: https://www.bestbuy.com/site/insignia-usb-3-0-memory-card-reader/5787406.p?skuId=5787406).

Put the microSD card in reader, the reader in a USB port, and type <code>ls -1 /Volumes</code> in a terminal. Note the name of the microSD volume; for example, VOL1 in the output below:
$ ls -1 /Volumes
Macintosh HD
Preboot
VOL1
$

Unmount the reader, unplug it and re-run <code>ls -1 /Volumes</code>. Verify the microSD volume name is no longer listed and then re-insert the USB reader.

Find the mount point of your microSD volume; for example, disk3 in the output below:
$ diskutil list VOL1
/dev/disk3 (external, physical):
#: TYPE NAME SIZE IDENTIFIER
0: FDisk_partition_scheme *31.4 GB disk3
1: DOS_FAT_16 VOL1 256.0 MB disk3s1
2: Linux 30.0 GB disk3s2
3: Linux_Swap 1.2 GB disk3s3
$

(For help on diskutil command, type <code>diskutil</code> to list all command verbs. For help on a specific verb, add the verb; for example, <code>diskutil partitionDisk</code>)

Destroy all the existing partitions on the microSD card and create two new ones:
# a 256MB, FAT16, DOS-compatible partition and
# a free space gap for the rest of the card

$ diskutil partitionDisk disk3 MBR "MS-DOS FAT16" VOL1 256MB "Free Space" VOL2 R
Started partitioning on disk3
Unmounting disk
Creating the partition map
Waiting for partitions to activate
Formatting disk3s1 as MS-DOS (FAT16) with name VOL1
512 bytes per physical sector
/dev/rdisk3s1: 499472 sectors in 62434 FAT16 clusters (4096 bytes/cluster)
bps=512 spc=8 res=1 nft=2 rde=512 mid=0xf8 spf=244 spt=32 hds=32 hid=2 drv=0x80 bsec=500000
Mounting disk
Finished partitioning on disk3
/dev/disk3 (external, physical):
#: TYPE NAME SIZE IDENTIFIER
0: FDisk_partition_scheme *31.4 GB disk3
1: DOS_FAT_16 VOL1 256.0 MB disk3s1
$

Change your current working directory to the new FAT16 partition and then pickup with the untar instruction in the parent prep section.

$ cd /Volumes/VOL1/

= Installation =

Execute the following commands. Make sure there is an internet connection available otherwise setting up the apk mirrors will fail.

setup-alpine

Set the mapping keyboard, the timezone, how to connect to the network ('''dhcp''' is the best method), say '''none''' at <code>save config</code> and <code>save cache</code>.

apk update

Raspberry Pi has no battery for his hardware clock, so synchronize with an ntp server:

apk add chrony
service chronyd restart
apk add e2fsprogs
mount /dev/mmcblk0p2 /mnt # The second partition, in ext4 format, where Alpine Linux is installing in sys mode
setup-disk -m sys /mnt
mount -o remount,rw /media/mmcblk0p1 # An update in the first partition is required for the next reboot.

Clean up the boot folder in the first partition to drop unused files:

rm -f /media/mmcblk0p1/boot/*
cd /mnt # We are in the second partition
rm boot/boot # Drop the unused symbolink link

Move the image and <code>init ram</code> for Alpine Linux into the right place:

mv boot/* /media/mmcblk0p1/boot/
rm -Rf boot
mkdir media/mmcblk0p1 # It's the mount point for the first partition on the next reboot

Don't worry about the error with the following:

ln -s media/mmcblk0p1/boot boot

Update <code>/etc/fstab</code>:

echo "/dev/mmcblk0p1 /media/mmcblk0p1 vfat defaults 0 0" >> etc/fstab
sed -i '/cdrom/d' etc/fstab # Of course, you don't have any cdrom or floppy on the Raspberry Pi
sed -i '/floppy/d' etc/fstab
cd /media/mmcblk0p1

If you want to active edge repository
sed -i '/edge/s/^#//' etc/apk/repositories # But enable the repository for community if you want vim, mc, php, apache, nginx, etc.

For the next boot, indicate that the root filesystem is on the second partition. If the cmdline.txt file
contains a line that starts with <code>/root</code>, then use sed:

sed -i 's/^/root=\/dev\/mmcblk0p2 /' /media/mmcblk0p1/cmdline.txt
reboot

otherwise, use echo:

echo "/root=/dev/mmcblk0p2" >> cmdline.txt

That works on '''Raspberry Pi 3B''' and '''1B''', but if you have the '''1B''' version, let's be very, very patient (several tens of minutes).

If a hard disk is connected via '''usb''', you can replace the <code>/dev/mmcblk0p2</code> above with <code>/dev/sda1</code>, for example.

If you don't like the '''sed''' above and its expressions, you can use a nano editor instead after executing the following command:

apk add nano

= Post-installation =

The '''Raspberry Pi (RPI)''' has no battery to keep the time updated. Therefore, we need to enable the right service to synchronize with an ntp server:

rc-update del hwclock boot
rc-update add swclock boot
service hwclock stop
service swclock start

Update and upgrade the system:

apk update
apk upgrade

If you want a cool editor ({{Pkg|vim}}), a file manager ({{Pkg|mc}}), and to determine which tasks are running and which services are starting on boot ({{Pkg|htop}}), add the right packages:

apk add vim mc htop
htop
rc-update

The '''RPI 3B''' has wifi on board for networking, so start the service for the encrypted key on wpa2 protocol:

apk add wpa_supplicant
rc-update add wpa_supplicant boot
service wpa_supplicant start
setup-interfaces
Replace the IP address by dhcp for all the interfaces if necessary; select the SSID network for wifi; and add password.
ip addr # to know the IP address for all interfaces

If you want to connect on your remote RPI via <code>ssh</code>, an additional user (''foo'') and the {{Pkg|sudo}} package are required because it's forbidden to connect as root:

apk add sudo
adduser foo
adduser foo wheel
visudo

Uncomment line #82 with <code>wheel ALL=(ALL) ALL</code>. If {{Pkg|vim}} is installed, save the changes by typing '''Esc :x'''

= See also =

* [[Raspberry Pi]]
* [[Raspberry Pi 3 - Setting Up Bluetooth]]
* [[Raspberry Pi 3 - Configuring it as wireless access point -AP Mode]]
* [[Linux Router with VPN on a Raspberry Pi]]

[[Category:Installation]]

Classic install or sys mode on Raspberry Pi

2018-09-02T21:51:23Z

Mkbucc: /* Preparation */

A howto for classic installation, or "sys mode".

This method works with a desktop PC under Ubuntu and other Linuxes.

= Preparation =

Download the archive from the '''Rasperry Pi armhf''' link [https://alpinelinux.org/downloads/ here].
'''Sha256''' and '''GPG''' links appear next to the link to check the download.

On a class 10 sd-card with a size of 8Go or more, create two partitions:-
* First in '''fat16''' with size of 256Mo. You may have to check <code>boot</code> and <code>lba</code> flags
* Second in '''ext4''' with the remaining place

Eject and insert your SD card in order to recognize all the partitions.

Now go into the first partition ('''fat16''').

Untar the archive with {{pkg|tar}}:
tar zxvf ~/Download/alpine-rpi-*-armhf.tar.gz

Due to a bug, it is recommended to add a file named <code>usercfg.txt</code> into the partition. The file should contain the following single line:

enable_uart=1

Eject the SD card properly, insert it into the Raspberry Pi, plug a usb keyboard in plus the HDMI and network cables, and power on.

When a prompt displays, connect as root without a password.

Summary: Add OSX diskutil instructions for creating FAT16 partition on microSD

== OSX Preparation: creating a FAT16 partition on microSD ==

To create a FAT16 partition with OSX, use the diskutil program and a USB microSD card reader (I used an older version of this: https://www.bestbuy.com/site/insignia-usb-3-0-memory-card-reader/5787406.p?skuId=5787406).

Put the microSD card in reader, the reader in a USB port, and type <code>ls -1 /Volumes</code> in a terminal. Note the name of the microSD volume; for example, VOL1 in the output below:
$ ls -1 /Volumes
Macintosh HD
Preboot
VOL1
$

Unmount the reader, unplug it and re-run <code>ls -1 /Volumes</code>. Verify the microSD volume name is no longer listed and then re-insert the USB reader.

Find the mount point of your microSD volume; for example, disk3 in the output below:
$ diskutil list VOL1
/dev/disk3 (external, physical):
#: TYPE NAME SIZE IDENTIFIER
0: FDisk_partition_scheme *31.4 GB disk3
1: DOS_FAT_16 VOL1 256.0 MB disk3s1
2: Linux 30.0 GB disk3s2
3: Linux_Swap 1.2 GB disk3s3
$

(For help on diskutil command, type <code>diskutil</code> to list all command verbs. For help on a specific verb, add the verb; for example, <code>diskutil partitionDisk</code>)

Destroy all the existing partitions on the microSD card and create two new ones:
# a 256MB, FAT16, DOS-compatible partition and
# a free space gap for the rest of the card

$ diskutil partitionDisk disk3 MBR "MS-DOS FAT16" VOL1 256MB "Free Space" VOL2 R
Started partitioning on disk3
Unmounting disk
Creating the partition map
Waiting for partitions to activate
Formatting disk3s1 as MS-DOS (FAT16) with name VOL1
512 bytes per physical sector
/dev/rdisk3s1: 499472 sectors in 62434 FAT16 clusters (4096 bytes/cluster)
bps=512 spc=8 res=1 nft=2 rde=512 mid=0xf8 spf=244 spt=32 hds=32 hid=2 drv=0x80 bsec=500000
Mounting disk
Finished partitioning on disk3
/dev/disk3 (external, physical):
#: TYPE NAME SIZE IDENTIFIER
0: FDisk_partition_scheme *31.4 GB disk3
1: DOS_FAT_16 VOL1 256.0 MB disk3s1
$

Change your current working directory to the new FAT16 partition and then pickup with the untar instruction in the parent prep section.

$ cd /Volumes/VOL1/

= Installation =

Execute the following commands. Make sure there is an internet connection available otherwise setting up the apk mirrors will fail.

setup-alpine

Set the mapping keyboard, the timezone, how to connect to the network ('''dhcp''' is the best method), say '''none''' at <code>save config</code> and <code>save cache</code>.

apk update

Raspberry Pi has no battery for his hardware clock, so synchronize with an ntp server:

apk add chrony
service chronyd restart
apk add e2fsprogs
mount /dev/mmcblk0p2 /mnt # The second partition, in ext4 format, where Alpine Linux is installing in sys mode
setup-disk -m sys /mnt
mount -o remount,rw /dev/mmcblk0p1 # An update in the first partition is required for the next reboot.

Clean up the boot folder in the first partition to drop unused files:

rm -f /media/mmcblk0p1/boot/*
cd /mnt # We are in the second partition
rm boot/boot # Drop the unused symbolink link

Move the image and <code>init ram</code> for Alpine Linux into the right place:

mv boot/* /media/mmcblk0p1/boot/
rm -Rf boot
mkdir media/mmcblk0p1 # It's the mount point for the first partition on the next reboot

Don't worry about the error with the following:

ln -s media/mmcblk0p1/boot boot

Update <code>/etc/fstab</code>:

echo "/dev/mmcblk0p1 /media/mmcblk0p1 vfat defaults 0 0" >> etc/fstab
sed -i '/cdrom/d' etc/fstab # Of course, you don't have any cdrom or floppy on the Raspberry Pi
sed -i '/floppy/d' etc/fstab
cd /media/mmcblk0p1

If you want to active edge repository
sed -i '/edge/s/^#//' etc/apk/repositories # But enable the repository for community if you want vim, mc, php, apache, nginx, etc.

For the next boot, indicate that the root filesystem is on the second partition:

sed -i 's/^/root=\/dev\/mmcblk0p2 /' cmdline.txt
reboot

That works on '''Raspberry Pi 3B''' and '''1B''', but if you have the '''1B''' version, let's be very, very patient (several tens of minutes).

If a hard disk is connected via '''usb''', you can replace the <code>/dev/mmcblk0p2</code> above with <code>/dev/sda1</code>, for example.

If you don't like the '''sed''' above and its expressions, you can use a nano editor instead after executing the following command:

apk add nano

= Post-installation =

The '''Raspberry Pi (RPI)''' has no battery to keep the time updated. Therefore, we need to enable the right service to synchronize with an ntp server:

rc-update del hwclock boot
rc-update add swclock boot
service hwclock stop
service swclock start

Update and upgrade the system:

apk update
apk upgrade

If you want a cool editor ({{Pkg|vim}}), a file manager ({{Pkg|mc}}), and to determine which tasks are running and which services are starting on boot ({{Pkg|htop}}), add the right packages:

apk add vim mc htop
htop
rc-update

The '''RPI 3B''' has wifi on board for networking, so start the service for the encrypted key on wpa2 protocol:

apk add wpa_supplicant
rc-update add wpa_supplicant boot
service wpa_supplicant start
setup-interfaces
Replace the IP address by dhcp for all the interfaces if necessary; select the SSID network for wifi; and add password.
ip addr # to know the IP address for all interfaces

If you want to connect on your remote RPI via <code>ssh</code>, an additional user (''foo'') and the {{Pkg|sudo}} package are required because it's forbidden to connect as root:

apk add sudo
adduser foo
adduser foo wheel
visudo

Uncomment line #82 with <code>wheel ALL=(ALL) ALL</code>. If {{Pkg|vim}} is installed, save the changes by typing '''Esc :x'''

= See also =

* [[Raspberry Pi]]
* [[Raspberry Pi 3 - Setting Up Bluetooth]]
* [[Raspberry Pi 3 - Configuring it as wireless access point -AP Mode]]
* [[Linux Router with VPN on a Raspberry Pi]]

[[Category:Installation]]