Writing Init Scripts: Difference between revisions

From Alpine Linux
Line 5: Line 5:
Alpine Linux uses the [https://github.com/OpenRC/openrc OpenRC] init system to start services. Don't confuse OpenRC init with out system init (the first process that is executed aka pid 1). Many of the current init.d script found in Alpine Linux are takes from Gentoo. If you want to save time you could search [https://packages.gentoo.org/categories Gentoo's repository] for an existing initscript for your service. You can also check [https://wiki.gentoo.org/wiki/Handbook:X86/Working/Initscripts#Writing_initscripts Gentoo's wiki] for some additional OpenRC information.
Alpine Linux uses the [https://github.com/OpenRC/openrc OpenRC] init system to start services. Don't confuse OpenRC init with out system init (the first process that is executed aka pid 1). Many of the current init.d script found in Alpine Linux are takes from Gentoo. If you want to save time you could search [https://packages.gentoo.org/categories Gentoo's repository] for an existing initscript for your service. You can also check [https://wiki.gentoo.org/wiki/Handbook:X86/Working/Initscripts#Writing_initscripts Gentoo's wiki] for some additional OpenRC information.


NOTE: OpenRC recently added [documentation https://github.com/OpenRC/openrc/blob/master/service-script-guide.md] on how to write proper Init scripts
<strong>NOTE</strong>: OpenRC recently added [documentation https://github.com/OpenRC/openrc/blob/master/service-script-guide.md] on how to write proper Init scripts


If you cannot find an init.d script from Gentoo, or you just want to start to write your own init.d scripts, we provide you with some basic information on how to write simple OpenRC init scripts.
If you cannot find an init.d script from Gentoo, or you just want to start to write your own init.d scripts, we provide you with some basic information on how to write simple OpenRC init scripts.

Revision as of 18:24, 20 February 2018

This material is work-in-progress ...

Do not follow instructions here until this notice is removed.
(Last edited by Clandmeter on 20 Feb 2018.)

Introduction

Alpine Linux uses the OpenRC init system to start services. Don't confuse OpenRC init with out system init (the first process that is executed aka pid 1). Many of the current init.d script found in Alpine Linux are takes from Gentoo. If you want to save time you could search Gentoo's repository for an existing initscript for your service. You can also check Gentoo's wiki for some additional OpenRC information.

NOTE: OpenRC recently added [documentation https://github.com/OpenRC/openrc/blob/master/service-script-guide.md] on how to write proper Init scripts

If you cannot find an init.d script from Gentoo, or you just want to start to write your own init.d scripts, we provide you with some basic information on how to write simple OpenRC init scripts.

Primary information about the OpenRC format can be found in the OpenRC man page openrc-run.

apk add openrc-doc man

man openrc-run

Minimal Templates

Every init.d script you write needs to start with a shebang like:

#!/sbin/openrc-run

Services relying on OpenRC exclusively

#!/sbin/openrc-run

command="/path/to/command"

Services supervised by s6

Notes:

  • Install and configure the s6-scan service to start on system boot
  • Exclude start(), stop() and status() functions in order for s6 supervision to work reliably. OpenRC has built-in equivalent functions which invoke the necessary s6 commands.
  • Include a depend() stanza to ensure that the s6-svscan service is already running.
  • Add a start_pre() stanza to symlink the service directory into the scan directory, because the /etc/init.d/bootmisc scripts cleans out the /run directory on system boot.
#!/sbin/openrc-run

name="foo"
supervisor="s6"
s6_service_path="${RC_SVCDIR}/s6-scan/${name}"

depend() {
    need s6-svscan
}

start_pre() {
    if [ ! -L "${RC_SVC_DIR}/s6-scan/${name}" ]; then
        ln -s "/path/to/${name}/service/dir" "${RC_SVCDIR}/s6-scan/${name}"
    fi
}

The rest of the below basic example could be omitted, but that would most probably leave you with an non working initd script.

Basic example

#!/sbin/openrc-run
  
name=$RC_SVCNAME
cfgfile="/etc/$RC_SVCNAME/$RC_SVCNAME.conf"
command="/usr/bin/my_daemon"
command_args="--my-daemon-args"
command_user="my_system_user"
pidfile="/run/$RC_SVCNAME/$RC_SVCNAME.pid"
start_stop_daemon_args="--args-for-start-stop-daemon"
command_background="yes"

depend() {
        need net
}

start_pre() {
        checkpath --directory --owner $command_user:$command_user --mode 0775 \
                /run/$RC_SVCNAME /var/log/$RC_SVCNAME
}

start, stop, restart functions

OpenRC defined a few basic functions ie: start, stop, restart. These functions are defined by default but can be overwritten by defining your own set of functions. This is generally only necessary if you want to do something special which is not provided by the default start/stop/restart implementations.

start

start() {
    ebegin "Starting mydaemon"
    start-stop-daemon --start \
        --exec /usr/sbin/mydaemon \
        --pidfile /var/run/mydaemon.pid \
        -- \
        --args-for-mydaemon
    eend $?
}

stop

restart

Daemon, Forking, Logging

TODO...