Configure a Wireguard interface (wg)

From Alpine Linux
Revision as of 17:35, 17 April 2024 by Fossdd (talk | contribs) (add Use with network interfaces)

WireGuard has become a nearly ubiquitous vpn solution for multiple platform and is available in the community repository since Alpine 3.10. WireGuard itself is now integrated into the linux kernel since v5.6. Only the userland configuration tools are required.

Install required packages

The most straightforward method, and the one recommended in WireGuard documentation, is to use wg-quick.

Install wireguard-tools, iptables, and sysctl:

apk add wireguard-tools-wg-quick
apk add iptables
apk add sysctl

Create Server Keys and Interface Config

Create a server private and public key:

wg genkey | tee server.privatekey | wg pubkey > server.publickey

Then, we create a new config file /etc/wireguard/wg0.conf using these new keys:

[Interface]
Address = 192.168.2.1/24
ListenPort = 45340
PrivateKey = <server private key value> # the key from the previously generated privatekey file
PostUp = iptables -A FORWARD -i %i -j ACCEPT; iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE;iptables -A FORWARD -o %i -j ACCEPT
PostDown = iptables -D FORWARD -i %i -j ACCEPT; iptables -t nat -D POSTROUTING -o eth0 -j MASQUERADE;iptables -D FORWARD -o %i -j ACCEPT

[Peer]
PublicKey = <client public key value> # obtained from client device via wireguard connection setup process
AllowedIPs = 192.168.2.2/32

The PostUp and PostDown iptable rules forward traffic from the wg0 subnet (192.168.2.1/24) to the lan subnet on interface eth0.

Refer to this WireGuard documentation for information on adding peers to the config file.

Bring up the new wg0 interface: ,

wg-quick up wg0

To take it down, we can use wg-quick down wg0 which will clean up the interface and remove the iptables rules. Note: If running in a Docker container, you will need to run with --cap-add=NET_ADMIN to modify your interfaces.

Use with network interfaces

To enable connecting with Wireguard on boot, open your /etc/network/interfaces and add this information after your auto other network interfaces:

auto wg0
iface wg0 inet static
pre-up wg-quick up /etc/wireguard/wg0.conf

Enable IP Forwarding

With a NAT destination rule in place on your router, you should be able connect to the wireguard instance and access the host. However, if you intend for peers to be able to access external resources (including the internet), you will need to enable ip forwarding.

Edit the file /etc/sysctl.conf (or a .conf file under /etc/sysctl.d/) and add the following line:

net.ipv4.ip_forward = 1

Add the sysctl service to run at boot:

rc-update add sysctl 

Then either reboot or run sysctl -p /etc/sysctl.conf to reload the settings. To ensure forwarding is turned on, run sysctl -a | grep ip_forward and ensure net.ipv4.ip_forward is set to 1.

Running with modloop

If you are running from a RAM disk, you can't modify the modloop.

You can get around it by unpacking the modloop, mounting the unpacked modules folder, then installing WireGuard.

#!/bin/sh
apk add squashfs-tools # install squashfs tools to unpack modloop
unsquashfs -d /root/squash /lib/modloop-lts # unpack modloop to root dir
umount /.modloop # unmount existing modloop
mount /root/squash/ /.modloop/ # mount unpacked modloop
apk del wireguard-lts # uninstall previous WireGuard install
apk add wireguard-lts
apk add wireguard-tools

You can repack the squash filesystem or put this script in the /etc/local.d/ path so it runs at boot-up.