LXC

Linux Containers (LXC) provides containers similar BSD Jails, Linux VServer and Solaris Zones. It gives the impression of virtualization, but shares the kernel and resources with the "host".

Installation

Install the required packages:

apk add lxc bridge

Prepare network on host

Set up a bridge on the host. Example /etc/network/interfaces:

auto br0
iface br0 inet dhcp
    bridge-ports eth0

Create a network configuration template for the guests, /etc/lxc/lxc.conf:

lxc.network.type = veth
lxc.network.link = br0
lxc.network.flags = up

Create a guest

Alpine Template

lxc-create -n guest1 -f /etc/lxc/lxc.conf -t alpine

This will create a /var/lib/lxc/guest1 directory with a config file and a rootfs directory.

Note that by default alpine template does not have networking service on, you will need to add it using lxc-console

Debian template

In order to create a debian template container you will need to install some packages:

apk add debootstrap rsync

Also you will need to turn off some grsecurity chroot options otherwise the debootstrap will fail:

echo 0 > /proc/sys/kernel/grsecurity/chroot_caps echo 0 > /proc/sys/kernel/grsecurity/chroot_deny_chroot echo 0 > /proc/sys/kernel/grsecurity/chroot_deny_mount echo 0 > /proc/sys/kernel/grsecurity/chroot_deny_mknod echo 0 > /proc/sys/kernel/grsecurity/chroot_deny_chmod

Please remember to turn them back on, or just simply reboot the system.

Now you can run:

SUITE=wheezy lxc-create -n guest1 -f /etc/lxc/lxc.conf -t debian

Starting/Stopping the guest

Create a symlink to the /etc/init.d/lxc script for your guest.

ln -s lxc /etc/init.d/lxc.guest1

You can start your guest with:

/etc/init.d/lxc.guest1 start

Stop it with:

/etc/init.d/lxc.guest1 stop

Make it autostart on boot up with:

rc-update add lxc.guest1

Connecting to the guest

By default sshd is not installed, so you will have to connect to a virtual console. This is done with:

lxc-console -n guest1

To disconnect from it, press Ctrl+a q

Deleting a guest

Make sure the guest is stopped and run:

lxc-destroy -n guest1

This will erase eerything, without asking any questions. It is equivalent to:

rm -r /var/lib/lxc/guest1

Advanced

Using static IP

If you're using static IP, you need to configure this properly. First add these two options to you /var/lib/lxc/guest1/config:

lxc.network.ipv4 = <IP-to-use>
lxc.network.ipv4.gateway = <IP-of-gateway-to-use>

And change /var/lib/lxc/guest1/rootfs/etc/network/interfaces from

#auto lo
    iface lo inet loopback
auto eth0
    iface eth0 inet dhcp

to

#auto lo
    iface lo inet loopback
auto eth0
    iface eth0 inet static

mem and swap

vim /boot/extlinux.conf

APPEND initrd=initramfs-3.10.13-1-grsec root=UUID=7cd8789f-5659-40f8-9548-ae8f89c918ab modules=sd-mod,usb-storage,ext4 quiet cgroup_enable=memory swapaccount=1

checkconfig

lxc-checkconfig

Kernel configuration not found at /proc/config.gz; searching... Kernel configuration found at /boot/config-3.10.13-1-grsec --- Namespaces --- Namespaces: enabled Utsname namespace: enabled Ipc namespace: enabled Pid namespace: enabled User namespace: missing Network namespace: enabled Multiple /dev/pts instances: enabled --- Control groups --- Cgroup: enabled Cgroup clone_children flag: enabled Cgroup device: enabled Cgroup sched: enabled Cgroup cpu account: enabled Cgroup memory controller: missing Cgroup cpuset: enabled --- Misc --- Veth pair device: enabled Macvlan: enabled Vlan: enabled File capabilities: enabled Note : Before booting a new kernel, you can check its configuration usage : CONFIG=/path/to/config /usr/bin/lxc-checkconfig

VirtualBox

In order for network to work on containers you need to set "Promiscuous Mode" to "Allow All" in VirtualBox settings for the network adapter.