User:Mhavela/squark-auth-snmp: Difference between revisions
(Re-inserted notes about web-based authentication (still not sure if they belong here)) |
m (User:Mhavela/sandbox2 moved to User:Mhavela/squark-auth-snmp: I felt for it :-)) |
(No difference)
|
Revision as of 02:33, 23 December 2011
This material is work-in-progress ... Do not follow instructions here until this notice is removed. |
Using squark-auth-snmp
Introduction
This document describes how to use 'squark-auth-snmp' as squid authentication helper to obtain a username or other useful information from a switch.
'squark-auth-snmp' queries the switch via SNMP using standard MIBs to obtain various information.
The information is then injected into the squid access logs (which can help auditors when analysing the logs).
Switches that confirmed to function (at least in some degree):
- HP Procurve 5400zl
- HP Procurve 1810G 24GE
Confirm if "HP Procurve 2650" works
In some examples a IP-address might be mentioned. Change those to reflect your configuration.
Values such as <ip.of.switch> and other values marked as <something> should be replaced appropriately.
Configuring the switch
Enable SNMP Lookups
We need a 'SNMP community' configured on the switch (which has at least 'read-only' or 'restricted' permissions).
If your switch does not have such 'SNMP community', you will need to create one.
You will benefit in reading you manual to figure out how to apply the changes to your own switch.
Start by loggin on to your switch (use telnet, ssh or a serial cable. The manual that came with your switch will describe how this is done for your switch).
View your snmp-server settings
Run the following command to view your current snmp-settings
show snmp-server
Create a SNMP community
In this case we will create a SNMP community called "public" and giving it "restricted" rights.
We will also configure the switch to send SNMP replies from the same IP address as the one on which the corresponding SNMP request was received.
configure snmp-server community "public" restricted snmp-server response-source dst-ip-of-request exit
Run the above commands (exactly as they appear above) on all switches that the squark-auth-snmp plugin will run snmp queries against.
Link Layer Discovery Protocol
If you have multiple switches in your environment, Link Layer Discovery Protocol (LLDP) should be enabled in order for 'squark-auth-snmp' to work properly.
If the IP of the switch that you have specified is a core switch (such as in a star topology network), and all the switches in your network have LLDP enabled (usually enabled by default), then your network topology should be automatically discoverable.
web-based authentication
It is possible to configure HP Procurve switches to do port-based web authentication.
A network device initiates traffic on a port, and is assigned to a "guest" vlan with limited or no network access.
A browser needs to be opened, and the user is given a user-name and password prompt.
For more information on configuring web-based authentication on an HP switch, see this link.
Configure squid & squark
Install squark
apk add squark
Configure squid
We assume you installed squid and done some initial configuration to get it working.
The below examples should replace or append values to your working '/etc/squid/squid.conf'.
General squid.conf modifications
Change (or edit) '/etc/squid/squid.conf' to reflect the following:
# Logging logformat squark %ts.%03tu %6tr %>a %Ss/%03>Hs %<st %rm %ru %un %Sh/%<A %mt %rG access_log /var/log/squid/access.log squark # Permissions cache_effective_user squid cache_effective_group squid # Allow hosts on <some.zone> to access internet http_access allow <some.zone> Zone_SquarkAuth
As you can see in the above example, we refer to the acl "Zone_SquarkAuth" which is not yet created.
Below examples will describe how to create it depending on your needs.
Configure squark-auth-snmp to use SNMPv2c
Change (or edit) '/etc/squid/squid.conf' to reflect the following:
# External ACL squid auth helper external_acl_type squark_auth children-startup=1 children-max=1 ttl=5 negative_ttl=2 concurrency=128 grace=10 \ %SRC /usr/bin/squark-auth-snmp -f "%N-%i-%M" -c public -r 10.82.96.1 -i eth1.96 -R 10.82.72.226 -v 96 acl Zone_SquarkAuth external squark_auth
Configure net-snmp
Describe this section in a way so the user understands if this is needed or not.
Install net-snmp
apk add net-snmp
Configure net-snmp
Basic configuration
Modify '/etc/snmp/snmpd.conf' to reflect at least the following:
rocommunity public default syslocation "Location of our equipment" sysservices 15 syscontact "ComputerDept <computerdept@foo.bar>"
SNMPv3 Configuration (optional)
Squark will use the configuration specified in '/etc/snmp/snmp.conf' when snmpv3 is specified as the preferred version of SNMP to use. Ensure that you have at least the following in /etc/snmp/snmp.conf:
defContext none defSecurityName <username> defAuthPassphrase <password> defVersion 3 defAuthType MD5 defSecurityLevel authNoPriv
Start using it
Start it all up
/etc/init.d/squid start /etc/init.d/snmpd start
Make sure to configure you services to autostart at next reboot
rc-update add squid default rc-update add snmpd default